To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 16424
16423  |  16425
Subject: 
Re: Mindstorms Automatic Train Control Questions
Newsgroups: 
lugnet.robotics
Date: 
Fri, 2 Nov 2001 01:05:52 GMT
Viewed: 
1792 times
  
In lugnet.robotics, Dean Husby writes:
> Steve Baker wrote:
> > You'll also see mention of the 'MicroScout' - that's basically just a
> > box containing a single motor with a single light sensor and something
> > that Lego calls 'programmability' - but which really only lets you string
> > together an utterly minimal set of canned commands in a fixed unchanging
> > sequence.  The Microscout has to be programmed via it's light sensor so
> > you can't talk to it via the IR tower.  I had to program a Scout to send
> > the programming commands to the Microscout...it was a waste of time.
> > 
> > CONCLUSION:
> > 
> >   With care, the Scout can be a useful (cheap!) ADDITION to RCX in
> > some specific applications.
> > 
> >   But: *BEWARE* the MicroScout will almost certainly *NOT* do anything
> > useful for you.  IMHO, they are about as useful to serious robotic
> > as a JarJar Binks minifig!
> 
> The micro scout makes a good 3rd Motor to the Scout. Since you can hook
> up a Microscout to the RED LED on the Scout and it will act as a third
> motor. It only has one speed but is back and forth and DOES have a cool
> ability of stopping it's self if you STALL the motor. Handy for some
> things. When you use the LEGO remote or tell motor port 3 to do
> something it's instant. There is no annoying noise before the microscout
> does something. It's a slave.
> 
> I've managed to make a camera mount with the Scout. JUST enough room to
> pull it off.
> 
> I believe there is a way to get passive light values from the Light
> Sensor too, it's a separate command in NQC.
> 
> Dean

Could a micro scout be used to manipulate switch points ?  Might be an
interesting use for the micro scout. Will it respond to the handheld IR remote
control ? Is there any way to make it address selectable ?  Hmmmmmm, there still
may be a few DDKs at some walmarts in my region.

Ray



Message has 1 Reply:
  Re: Mindstorms Automatic Train Control Questions
 
You can use micro-scout to control switch point, connected by fibre cable with a scout. I tested it, no problem, so that you can use two outpput ports on scout to control tracks. Zhengrong ---...--- (...) (25 years ago, 2-Nov-01, to lugnet.robotics)

Message is in Reply To:
  Re: Mindstorms Automatic Train Control Questions
 
(...) The micro scout makes a good 3rd Motor to the Scout. Since you can hook up a Microscout to the RED LED on the Scout and it will act as a third motor. It only has one speed but is back and forth and DOES have a cool ability of stopping it's (...) (25 years ago, 2-Nov-01, to lugnet.robotics)

4 Messages in This Thread:

Entire Thread on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact

This Message and its Replies on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact
    

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR