 | | RE: Love the new Music capability with the new firmware!
|
|
(...) That IS cool. Now the problem is to figure out if this new feature was implemented using the exisiting ROM or if the entry points have changed. Has anybody tried to run legOS or pbForth on the new RCX 2.0? (Maybe I can use this as an excuse to (...) (25 years ago, 24-Aug-01, to lugnet.robotics, lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
 | | Love the new Music capability with the new firmware!
|
|
I don't know if people have discussed this already or not, but I'm just playing around with the new firmware now and I can finally do what I have wanted to do for 3 years, and that is to make the frequency played by the RCX be a function of a (...) (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | Need help with RcxCC: I get "The system cannon find the file specified" error.
|
|
Hi. I'm having problems with RcxCC. I hope you can help me. I've just installed RcxCC v. 3.2. I use Win2000 and RIS 1.5. When I compile a simple program, I get following error message: " Win32 Error. Code: 2. The system cannot find the file (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Power inlet to RCX 1.5?
|
|
(...) I'd use a 9V 1.5A _regulated_ power supply. Lower ampere ratings should also work until you stall three motors ... Jürgen (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Power inlet to RCX 1.5?
|
|
(...) Yes, but there are only pictures, no circuit diagram. It is very hard to figure out a circuit from photos, it is much easier if you really have the thing. Jürgen (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | Re: bushing (bush) question
|
|
In lugnet.robotics, Bram Lambrecht writes: [...] (...) I think this is correct. I once built the "Aliens" type walker, (URL) . I used Type 2 originally and found that after the thing would walk a few meters one of the legs would pop off. Didn't have (...) (25 years ago, 24-Aug-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: Lego Dacta Control Lab software
|
|
Looks like only PC is available on that site. Could you give me a site for the Mac version? Thanks for your time, (...) (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | RE: bushing (bush) question
|
|
(...) Type 2 is newer, probably because the Type 1's were too hard to take off the axle. I've noticed that most of my loose Type 1's have a hairline fracture on one side. (...) All the parts with teeth were essentially replaced with functional (...) (25 years ago, 24-Aug-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: How to communication between RCXs without PC?
|
|
You know I had finished my control program in NQC, it is not so simple, but I need to control LEGO Train in smooth speed, NQC is limitation, so I want to use legOS for one of RCX, could you give me some hints for sending/receiving NQC style message (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: How to communication between RCXs without PC?
|
|
(...) As far as I know, it is not possible to communicate between legOS and NQC using LNP. I think it would be possible to directly drive the IR port from your own code to send and recieve NQC-style communications, but the ability isn't built into (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: How to communication between RCXs without PC?
|
|
Thanks a lot, Michael. Is it possible to commucate between two RCXs and one uses legOS and another one uses NQC? I will read them, but could you give me a simplest sample here? (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: How to communication between RCXs without PC?
|
|
(...) Yes. Read the HOWTO section on LNP, which stands for legOS Networking Protocol. If you have any questions the HOWTO doesn't answer, feel free to ask here. (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | How to communication between RCXs without PC?
|
|
I am thinking to convert NQC program to legOS, but I am not sure how to communicate between RCXs without PC (similar as SendMessage() and Message() in NQC), does anyone have experience? Zhengrong (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: bushing (bush) question
|
|
(...) Based on my experience, out of over 200 Type 1's that I own, only a few have ever split in half. Having recently acquired a used 8880 supercar (which uses Type 2's), I now have over 20 split Type 2's, and that number keeps increasing with use. (...) (25 years ago, 24-Aug-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: Power inlet to RCX 1.5?
|
|
(...) But what sort of Voltage and Amperage do you use with that connection? Coz, with me it won't work very well with a couple of adapters putting out 6 to 12 Volts (max. 1.25 A). Grtz., Remko (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Power inlet to RCX 1.5?
|
|
(...) Check out this site, Jürgen: (URL) least it used to be there... Grtz., Remko (25 years ago, 23-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Proper power supply for a 1.0?
|
|
(...) First off have you connected the right two plates? First, I'd suggest using a 9 volt battery to find the right two plates. The RCX has built in reversed polarity so with a 9volt battery you won't damage anything. THEN ONLY USE 9 volts (...) (25 years ago, 23-Aug-01, to lugnet.robotics.rcx)
|
| |
 | | Re: bushing (bush) question
|
|
(...) They're pretty much the same. But I think Type 1 bushings often have a tighter fit than Type 2 bushings. It really depends on each specific part and its particular tolerances. I have some Type 1's that are extrememly tight fitting, and others (...) (25 years ago, 23-Aug-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: bushing (bush) question
|
|
(...) I don't have any hard evidence, but I've always found that the type 2's (later version) grip a little more consistantly. The type 1's in my collection are either *really* tight or just moderately tight. Type 2's seem to be consistantly (...) (25 years ago, 23-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Migrating from IR tower/spirit.ocx to USB
|
|
Take a look at the code in (URL) some examples. -a "Dave Hallowell" <lego-robotics@crynwr.com> wrote in message news:NEBBLJAEMKLDMPB...ems.com... (...) (25 years ago, 23-Aug-01, to lugnet.robotics)
|