 | | Re: Maximum sample rate (turn rate) for rotation sensor
|
|
When using the standard firmware, sensors are sampled every 3 ms. The rotation sensor uses a quadrature encoder with a 1:4 gearing between the axle and the encoder, so there are 16 "ticks" per revolution of the axle. The decoding routine in the (...) (25 years ago, 21-Jul-01, to lugnet.robotics.rcx)
|
| |
 | | Re: Maximum sample rate (turn rate) for rotation sensor
|
|
The hardware can actually do (in my testing) up to ~3000 rpm with good accuracy. The problem is with the standard software, which cannot do more than some low number (which may or may not be 500, I don't recall) because of how it samples the HW. (...) (25 years ago, 20-Jul-01, to lugnet.robotics.rcx)
|
| |
 | | sample code for the remote patch (pc side)
|
|
Hi, is anybody using the remote patch ? I d be glad if anybody could post or send me some sample code for the pc-side where remote messages are send to the RCX. Thanx, Olaf Christ (25 years ago, 20-Jul-01, to lugnet.robotics.rcx.legos)
|
| |
 | | rotation sensor question
|
|
I installed leJOS, got it up and running, then read on the sourceforge site a support question about the rotation sensor, so I decided to test it out. I wrote a first cut at it and it didn't work, just like the support question suggested: import (...) (25 years ago, 20-Jul-01, to lugnet.robotics.rcx.java)
|
| |
 | | Maximum sample rate (turn rate) for rotation sensor
|
|
Does anyone know the correct maximum sampling rate for the Lego rotation sensor? This morning I noticed that Dave Baum gives a value of 1250 RPM in his "Definitive Guide" (page 29), but looking at (URL) see a value of 500 RPM. Which is correct? (...) (25 years ago, 20-Jul-01, to lugnet.robotics.rcx)
|
| |
 | | Re: Source switch?
|
|
Here is an LCAD drawing of a two-way power splitter that uses a single switch. (URL) post is at: (...) (25 years ago, 20-Jul-01, to lugnet.robotics)
|
| |
 | | Re: Source switch?
|
|
Tilman, Thanks for the input, I was afraid the "reversing" switch was going to be my only option. I have a pair of them, but I was hoping for a more elegant solution. jt (...) (25 years ago, 20-Jul-01, to lugnet.robotics)
|
| |
 | | Heat Seeking
|
|
Hi all! Does anyone have experience with any kind of heat sensor (that ones used in burglar alarms). A few years ago I heard something about a MIT robot that had a people following and shoot (water gun) behaviour. Despite they did it with patern (...) (25 years ago, 19-Jul-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Mystery Part
|
|
Hehehehe... I have to laugh, Brian. Other people have told you that it is a "Brick Separator", and it is extremely useful. The reason that I am laughing is that when I was just coming out of my dark ages almost exactly two years ago... I was just as (...) (25 years ago, 19-Jul-01, to lugnet.robotics.rcx)
|
| |
 | | Re: Yet another John Barnes endorsement
|
|
I've used John's "Four Channel Remote Control". It has always worked without fail. It works in a couple of modes, one of which is perfect for skid-steer type applications. There has obviously been a lot of thought put into his design. -Tim (...) (25 years ago, 19-Jul-01, to lugnet.robotics)
|
| |
 | | RE: Source switch?
|
|
There just to be a "reversing" switch. It has one output and one input. You put a technic axle trough it to operate it, and it has 4 positions: forward, off, reverse, off. You can rig two of these together to get the function you are looking for. (...) (25 years ago, 19-Jul-01, to lugnet.robotics)
|
| |
 | | Source switch?
|
|
I've look in a few Dacta catalogs and haven't found what I was looking for, so I figured I'd ask the experts. Is there a LEGO electric switch that has one input and can switch between two outputs? Basicly I want to have a power supply come into the (...) (25 years ago, 19-Jul-01, to lugnet.robotics)
|
| |
 | | Re: Mystery Part
|
|
Search the Lugnet Guide for "brick separator" (...) (25 years ago, 19-Jul-01, to lugnet.robotics.rcx)
|
| |
 | | Re: Mystery Part
|
|
It is a handy tool for separating plates and bricks. -- Bob Fay rfay@we.mediaone.net (URL) Bagnall" <bbagnall@escape.ca> wrote in message news:GGqCwD.4A7@lugnet.com... (...) year (...) (25 years ago, 19-Jul-01, to lugnet.robotics.rcx)
|
| |
 | | Mystery Part
|
|
The part I am having problems with is the dark-grey "foot pedal" looking part. Does anyone know what this is called or what it's used for? This has been the single biggest mystery to me since I bought the RIS kit over a year ago. (25 years ago, 19-Jul-01, to lugnet.robotics.rcx)
|
| |
 | | Re: Hardware Hacking of RCX
|
|
Roy Wood wrote: (snip) (...) (snip) Hmm... Heres one idea that'll look REALLY good on your resume :) Asymmetric Multiprocessing: RCX -> Basic Stamp 2p40 Use the RCX to communicate with a Parallax Basic Stamp. You can use a 5v regulator and control (...) (25 years ago, 19-Jul-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Hardware Hacking of RCX
|
|
(...) Hi, if want to use more sensors, then you might wanna look at (URL) a look at "3 Sharps using 1 input", heat up your soldering iron and have fun. Olaf Christ ---...--- If knowlege is power, how come the more I learn, the more I realize how (...) (25 years ago, 19-Jul-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: So where was everyone?
|
|
I has used that IR sensor to instead LEGO light sensor in RCX Controlled Trains, I have to say it is better than light sensor, and you don't need extra external light source. Zhengrong (...) (25 years ago, 19-Jul-01, to lugnet.robotics)
|
| |
 | | Re: Anybody got a RIS 2.0 yet?
|
|
(...) I've had mine a week already, but I pre-ordered it pretty early. How did you have it shipped? It seemed like shipping took a day or two longer than usual. Greg Betzel (25 years ago, 18-Jul-01, to lugnet.robotics)
|
| |
 | | Re: About SensorValueRaw(SENSOR_3) in Scout
|
|
(...) I'll fix the documentation for the next release. Dave (25 years ago, 19-Jul-01, to lugnet.robotics.scout)
|