 | | Re: legOS lcd management and thoughts on velocities
|
|
Hello jochen, (...) Thank you for your precision about your velocity handler For now, unfortunaly my the hard disk does not boot any more, and, fortunatly, my wife gave birth to a girl on wednesday! So I'll test all those nice handlers in a few (...) (26 years ago, 2-Feb-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Visual NQC 2001
|
|
Tim Webber pointed out to me that I must set the path to nqc.exe in the preferences. All is well now, thanks to Tim. -- Bob Fay California, USA rfay@we.mediaone.net (URL) (26 years ago, 2-Feb-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: TLG support
|
|
Hej Marco! (...) At least in Germany it works this way, too. No hassles - free replacement - great service. And until now they've always responded to my emails within 3 to 5 days... Happy building, Sven (26 years ago, 2-Feb-01, to lugnet.robotics)
|
| |
 | | Re: Pneumatic tubing...
|
|
(...) I use tubing that is typically used for the fuel lines in R/C airplanes. The tubing I bought is a little more "rubbery" than the lego tubing, but it still fits snuggly and works fine. I don't recall the ID, OD, etc. I just brought the lego (...) (26 years ago, 2-Feb-01, to lugnet.robotics)
|
| |
 | | Re: Anyone using Mac beige G3
|
|
(...) The serial ports weren't changed in a major way (still RS-422, etc), but there could have been subtle changes to the driver/receiver that would cause problems when hooked to marginal RS-232 devices (such as the IR tower). Fred Martin reported (...) (26 years ago, 2-Feb-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Pneumatic tubing...
|
|
(...) Has anyone tried the tubing from Pitsco/Dacta? See: (URL) It has a 1/8" ID and a 100 foot roll is $9.00. Is it like the tubing in Pneumatic sets or is it a hard plastic tubing instead of rubber? Thomas (26 years ago, 2-Feb-01, to lugnet.robotics)
|
| |
 | | Re: Pneumatic tubing...
|
|
(...) I believe that TLC has used the same tubing in a few non-pneumatic sets. I have one older pneumatic set here so I took a piece of tubing off of it and compared to some pieces that came off of the 6180 Hydro Search Sub. They appear to be quite (...) (26 years ago, 2-Feb-01, to lugnet.robotics)
|
| |
 | | Re: Short Circute Problem -- EMERGENCY
|
|
Hi guys , i tried all the tests mentioned in the HB assembly to find out which part of the HB blown. No luck. i am giving the results here: 1) Tested the interface and charger board - looks good. (Both power supply and the MAX232 circuit) 2) Tested (...) (26 years ago, 2-Feb-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Pneumatic tubing...
|
|
(...) the (...) Heck, ya got me ;-) Could be rubber, extremely soft polyurethane, or any number of compounds. You'd probably have to ask someone at TLG to identify it. I just bought a few packs of tubing from S@H to make sure I had enough. I get it (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
|
| |
 | | Re: Pneumatic tubing...
|
|
Dear Tom (...) it should have been in my original post) is the *material* and *x-sectional dimensions* for the LEGO pneumatic tubing. I have several sources for different kinds of tubing, but I want to get something as near identical to the LEGO (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
|