 | | serial data link
|
|
Hello All, I am trying to construct a device to replace the wires between the RS-232 converter and the Handy Board. Of the many questions involved in this sort of thing the first one I'm wondering if anybody has experience with is the matter of (...) (29 years ago, 4-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR Capture
|
|
(...) Try my IR routines available at (URL) should handle any # of data bits and any kinds of codes. e-mail me personally if you need more help. /Max (29 years ago, 3-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | IR Capture
|
|
Hi handyboarders! I'm currently controlling my camcorder pan (left-right) and tilt (up-down). My camera is a Nikon VN-310. I have a small (very small!) remote control to make it zoom, record, play, stop, etc. Now the thing is I want to use those (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Exp Board ETA?
|
|
Dear all, I must apologize for the long delay and stringing everyone along waiting for the Expansion Board. Even now I hesitate to answer for it is not pleasant to have nothing to show presently. Currently, I am working on the "Advanced Sensing" (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | RV: What is the better way to comunicate handyboard???
|
|
---...--- (...) the (...) help (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: int/float to string routines?%nu
|
|
[Jeff Keyzer] spake unto the ether: (...) Look at my serial I/O routines (Fred has them on the HB ftp/website with the other user-contributed software), specifically the functions in conio.c and serialio.c. I have both float-to-ASCII and (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | int/float to string routines?
|
|
Are there any int/float to string conversion routines available for the handy board? I'm sending data over the HB's serial port to my PC, and I need to be able to send data in string format. (I was originally sending data in its actual byte value, (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | RC bot base
|
|
Hello All, I have just purchased a new TYCO 9.6V Zig Zag car. It seems to have a fairly good base w/treads. I connected it to the handyboard (after gutting it and extending the wires ). Next I gave the motors a test and they both ran way too fast. (...) (29 years ago, 1-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Voltage problem
|
|
Well, further experimentation revealed that the chips are working, but with a quirk: If the the input of the '232 (pin 10) is tied to ground (pin 15), then the output (pin 7 of the '232, or pin 3 of J9) goes to the expected value of ~+10 volts. If, (...) (29 years ago, 1-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: servos?
|
|
The best places are the mail order hobby stores. They have the widest selection of servos and very good prices. The two I recommend are Tower Hobbies (www.towerhobbies.com) and Hobby Shack (www.hobbyshack.com). Either of these sells servos cheaper (...) (29 years ago, 1-Aug-97, to lugnet.robotics.handyboard)
|