To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *25134 (-20)
  Re: difference of generated code robolab<->NQC
 
(...) They both generate the same "kind" of code (specifically LASM bytecodes), but its unlikely that code would be identical. I'm sure there are certain patterns of code that are typical from Robolab programs, and certain patterns that are typical (...) (26 years ago, 3-Dec-00, to lugnet.robotics)
 
  Re: variable conversion in legOS
 
(...) This should work. Are you having problems with it? -Kekoa (26 years ago, 3-Dec-00, to lugnet.robotics)
 
  Re: Communication between NQC and VisualBasic
 
(URL) is my scanner source code made by NQC and Visual Basic In this case, i used StartTask(), StopTask(), SetVar(), Poll(), etc. from the LEGO's control. (26 years ago, 3-Dec-00, to lugnet.robotics.rcx.nqc)
 
  variable conversion in legOS
 
Could we convert a "float" variable in legOS to "int"? Thanks Yiu (26 years ago, 3-Dec-00, to lugnet.robotics)
 
  Re: motorized points - beating a dead horse
 
(...) I made a design that used a clutch gear and fit into a house. It worked very well when the switch was "warm" but wouldn't always trip it when it had been sitting for a bit. But it allowed the throw arm to fully though the switch one way or the (...) (26 years ago, 3-Dec-00, to lugnet.trains, lugnet.robotics)
 
  Re: motorized points - beating a dead horse
 
Try this: (URL) On! John Matthews (26 years ago, 3-Dec-00, to lugnet.trains, lugnet.robotics)
 
  Re: motorized points - beating a dead horse
 
Anyone know this address? Still hammering on solving this one! SteveB (...) (26 years ago, 3-Dec-00, to lugnet.trains, lugnet.robotics)
 
  Re: motorized points - beating a dead horse
 
Great tip, I never thought about using multible pulley/rubber bands! A big problem is the detent, the two at rest positions are very "sticky". Naybe more then multible rubber bands can even move. I'll give it a try. SteveB (...) (26 years ago, 3-Dec-00, to lugnet.trains, lugnet.robotics)
 
  Re: motorized points - beating a dead horse
 
Thanks Larry! And no need for embarassment I appreciate the help. SteveB (...) (26 years ago, 3-Dec-00, to lugnet.robotics)
 
  Re: Looking 4 robosport constructopedia scans
 
(...) I'm afraid you won't find them online. They are copyrighted by LEGO(r). If you want the scans buy the set. They *MAY* be available in 3 or 4 years if you wish to wait. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 3-Dec-00, to lugnet.robotics.rcx)
 
  Re: More Building Instructions for Scout?
 
(...) The Scout is programmable in the exact same way the RCX is. It's just smaller. All you need is a transmission tower and NQC to do it. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 3-Dec-00, to lugnet.robotics.scout, lugnet.books)
 
  Re: Books for Mindstorms
 
(...) Here's a couple - both by Robert Penfold: "Introducing Robotics with Lego Mindstorms"- ISBN 0-835934-2 (get it from Amazon) Lots of VB information "More Advanced Robots with Lego Mindstorms" - sorry, I don't know ISBN (26 years ago, 2-Dec-00, to lugnet.robotics, lugnet.books)
 
  Re: motorized points - beating a dead horse
 
(...) I'm not exactly sure about your setup (I'm not into trains), but how about a small pulley (half bushing) on the motor, driving a medium pulley (with the six holes) on an axle on whose other end is an 8t gear that drives a rack. That setup (...) (26 years ago, 2-Dec-00, to lugnet.trains, lugnet.robotics)
 
  Re: Books for Mindstorms
 
here's another (only in Japanese, but construction figures and nqc code are understandable to non-readers of Japanese): Title (English & Japanese) Written in List Price (\) Quantity Amount Jin Sato*s LEGOMindStorms Japanese \1900 1 \1900 TETUJIN (...) (26 years ago, 2-Dec-00, to lugnet.robotics, lugnet.books)
 
  difference of generated code robolab<->NQC
 
hi, i need to know if there is a difference between the code generated by Robolab and NQC. Both are running with the standard RCX Firmware, i also know that the compiled code of both is interpreted by the firmware. -> is the generated code the same (...) (26 years ago, 2-Dec-00, to lugnet.robotics)
 
  difference of generated code robolab<->NQC
 
hi, i need to know if there is a difference between the code generated by Robolab and NQC. Both are running with the standard RCX Firmware, i also know that the compiled code of both is interpreted by the firmware. -> is the generated code the same (...) (26 years ago, 2-Dec-00, to lugnet.robotics)
 
  Re: Turning off guided mode
 
Hold CTR and Click the ABOUT button. Scott (26 years ago, 2-Dec-00, to lugnet.robotics.rcx)
 
  More Building Instructions for Scout?
 
Do you know of any books and web sites with building instructions for models that use the Scout? Books and websites for Mindstorms include instructions for models that use the RCX , not the Scout. The Mindstorms Robotics Discovery Set provides a (...) (26 years ago, 2-Dec-00, to lugnet.robotics.scout, lugnet.books)
 
  Books for Mindstorms
 
The following books cover Mindstorms: 1. "Dave Baum's Definitive Guide to LEGO Mindstorms (Technology In Action)" by Dave Baum; November 1999 2. "The Unofficial Guide to LEGO MINDSTORMS Robots" by Jonathan B. Knudsen; November 1999 3. "Extreme (...) (26 years ago, 2-Dec-00, to lugnet.robotics, lugnet.books)  
 
  Turning off guided mode
 
I recently purchased a new system, and am reinstalling RIS. I hate the fact that I'm forced to go through guided mode, although I understand the rationale. I'm sure I saw a post here or somewhere on how to disable guided mode upon install. Can (...) (26 years ago, 2-Dec-00, to lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR