To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *24029 (-20)
  Freeware ICC11 and bad iasm11.exe?
 
Me again, I just got the ICC11 freeware from the Miniboard site and installed it, moving the crt.s over as it says to do in the docs, etc. I tried to compile the test compile of icc11 dhry.c printf.c and got a LOT of "phasing" errors, whatever that (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
 
  Miniboard download random failures
 
Hello, I just finished building a Miniboard using the HC811E2 processor. After swapping the Rx and Tx lines on my serial cable the download and reset switch do as the manual says. However, when I use dlm to download a program the bootstrap section (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
 
  Cybermaster on sale
 
Yesterday I saw that the Cybermaster is on sale at the Bart Smit toy shops in the Netherlands, now only fl. 169,- (approx US$ 70) instead of fl. 449,-. I bought just one... Emile. (26 years ago, 5-Oct-00, to lugnet.robotics)
 
  Re: The datalog
 
(...) Series of measurements. I've used it to measure light sensor values while doing a 360 degree turn next to a candle (disappointing, the candle made hardly a dent), and to measure raw values for touch sensors while pushing them slowly, 1/100mm (...) (26 years ago, 5-Oct-00, to lugnet.robotics.rcx.nqc)
 
  Re: Remote dead, what to do?
 
(...) Are you sure it is the remote? Maybe your RCX forgot its firmware, then the remote won't work. Jürgen (26 years ago, 5-Oct-00, to lugnet.robotics)
 
  Re: A neat idea for touch sensors
 
(...) That probably was me ((URL) That required a lot of Lego wires, put together in funny (...) I used five wires for convenience, since I have enough of them. But you can get by with just three wires if you connect them directly to the sensors and (...) (26 years ago, 5-Oct-00, to lugnet.robotics)
 
  Remote dead, what to do?
 
My remote control suddenly stopped working yesterday, and I immediately replaced the batteries, but that does not appear to have been the problem. What is the failure mode of these devices? Can the ir "bulb" burn out? If so, can it be replaced? Is (...) (26 years ago, 5-Oct-00, to lugnet.robotics)
 
  legOS doesn't work under NT?
 
I've been using legOS for Windows (Vamos-Wentworth's distribution) both on Windows 95 and Windows 98. Due to some reasons, I'll have to use a NT computer from now on (I'm the administrator). I installed everything, even the long filename support (...) (26 years ago, 5-Oct-00, to lugnet.robotics.rcx.legos)
 
  Re: A neat idea for touch sensors
 
Hi Rob, (...) Yes. But by looking carefully at the connectors it's not too hard to figure out how to do it. (...) I think it is just that in most cases parallel connections are needed, and you got to decide between the two possibilities if you want (...) (26 years ago, 5-Oct-00, to lugnet.robotics)
 
  Re: Is Extreme Creatures Good? (WAS: Re: US S@H Specials, Sep 20 - Sep 26, 2000)
 
(...) i'll (...) Not in my opinion, just a random collection of additional parts. There is an inventory at: (URL) I didn't buy the set, so maybe owners of the set would have a contrary opinion. Kerry (26 years ago, 5-Oct-00, to lugnet.market.shopping, lugnet.robotics.rcx, lugnet.robotics, lugnet.technic)
 
  serial communication
 
Hi.. I am also facing problem in serial communications. My problem is that I am trying to use the handyboard to drive a modem. I have used a cross-serial cable to connect my handyboard's external serial board to a modem. But whenever I run my app, (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
 
  R: communication via serial port
 
Using java and comm API ? ----- Original Message ----- From: Ray Tang <raytang_1@hotmail.com> To: <handyboard@media.mit.edu> Sent: Thursday, October 05, 2000 4:49 AM Subject: communication via serial port (...) and (...) the (...) a (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
 
  Re: The datalog
 
(...) If only the RCX could read it's own data... Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 5-Oct-00, to lugnet.robotics.rcx.nqc)
 
  ------( Terms of use for lugnet.com )------
 
TERMS OF USE FOR LUGNET.COM OVERVIEW AND DEFINITIONS lugnet.com ("LUGNET") is a privately owned Internet site designed and run primarily for the benefit of those who enjoy building with, discussing, collecting, buying & selling, trading, and (...) (26 years ago, 5-Oct-00, to lugnet.robotics.vc)
 
  ------( Welcome to lugnet.robotics.vc )------
 
Welcome to lugnet.robotics.vc, a LUGNET discussion group. CHARTER/PURPOSE: lugnet.robotics.vc (group): Focused discussion group for LEGO® MINDSTORMS™ Vision Command™ and related components: the LEGO Cam, vision recognition, algorithms, software (...) (26 years ago, 5-Oct-00, to lugnet.robotics.vc)
 
  Linux and v1.21 handyboard (fwd)
 
Hi, I've successfully located and compiled the IC files for the Handy Board. I can load and run programs on the board, BUT the digital input(s) are not being "seen". E.g. a simple program like: void test3(){ while (1){ if (digital(10)) printf("10 is (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
 
  Re: The datalog
 
(...) numbers. It can only log timers, sensors, variables, and the system watch. When a value is logged, its source is also logged. For example, AddToDatalog(Timer(1)) adds the current value of Timer 1 to the log and also stores that this entry came (...) (26 years ago, 5-Oct-00, to lugnet.robotics.rcx.nqc)
 
  communication via serial port
 
Hi, This isn't an off topic question... Has anyone tried programming the serial port (on Linux) to communicate with the Handyboard? I am working on an RF link between the Handyboard and a PC via serial communication, but I don't know much about (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
 
  Re: external power
 
I am by no means an expert on the subject but this is how I did it. First I cut the heavy motor power trace as shown in the FAQ. Next I soldered a four pin female header on top of the expansion board where the expansion board picks up power for the (...) (26 years ago, 4-Oct-00, to lugnet.robotics.handyboard)
 
  Re: A neat idea for touch sensors
 
(...) Those resistors in the Cybermaster touch sensors are in parallel to the sensor. You can read its value when the sensor is not pressed. Cybermaster uses it to figure out which sensor is connected to what port before starting the actual program. (...) (26 years ago, 4-Oct-00, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR