To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *23784 (-20)
  Re: New (ish) MINDSTORMS book in UK
 
There are 2 books from this author: (URL) Robotics with Lego Mindstorms Robert Penfold List Price: £12.99 Our Price: £10.39 You Save: £2.60 (20%) Availability: Usually dispatched within 24 hours Paperback - 270 pages (31 August, 2000) Bernard Babani (...) (26 years ago, 22-Sep-00, to lugnet.books, lugnet.robotics)
 
  Re: Strong gear assemble?
 
(...) Would the friction created be that much of a problem? Would the loss in efficiency be that noticeable? (Note: These are not rhetorical questions so a response would be appreciated :-) Jude (26 years ago, 22-Sep-00, to lugnet.robotics)
 
  Re: Batteries again, sorry
 
you're almost right. if you plugged a nimh pack into the HB's charge jack, the external pack would charge the internal batteries. but it would not power the board significantly. this is because the HB's charge jack includes a current-limit resistor (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
 
  Re: Strong gear assemble?
 
(...) A word of caution - the worm gears are certainly great for large gear reductions in small spaces, and it is usually easy to brace them well, but they have one disadvantage over a traditional gear train - they create more friction, and are (...) (26 years ago, 22-Sep-00, to lugnet.robotics)
 
  Batteries again, sorry
 
This should be my last question in terms of batteries. Assuming that I have nicads powering the HB, what effect would there be if, when the batteries were getting low, I connected a fully charged battery pack (e.g. containing the nimh cells) into (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
 
  Re: Batteries again
 
in theory this can be a problem. in practice, as long as the nicads are occasionally allowed to fully discharge, they'll last for a good long time in fine condition. fred In your message you said: (...) es. (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
 
  Which set contains the Temparature Sensor?
 
Hi, Does any set (except 9755 from Dacta) contain the Temparature Sensor? I tought that the Ultimate Accessory Set (3801) contained one and spend most of the last night searching in my collection for the damned thing (hey, I *really* thought that (...) (26 years ago, 22-Sep-00, to lugnet.robotics.rcx)
 
  Three new books about Lego Mindstorms
 
Hi I have found that three new books about Lego Mindstorms soon will be released. Lego Mindstorms for Dummies by Michael Meadhra, Arthur Griffith ISBN: 0764507672 Introducing Robotics with Lego Mindstorms Penfold, R A ISBN: 0859349012 More Advanced (...) (26 years ago, 22-Sep-00, to lugnet.robotics.rcx)  
 
  Anyone know where I can get RIS 1.0 to 1.5 Upgrade in the UK?
 
I've noticed that there are some parts in RIS 1.5 that don't exist in RIS 1.0, and that the programming software is supposed to be better (nesting of commands and such), but the Mindstorms site indicates that the upgrade (set #3803) is only (...) (26 years ago, 22-Sep-00, to lugnet.robotics)
 
  Batteries again
 
As Fred is recommending using nicads due to the constant trickle charge when connected to the mains adapter I have a question regarding the nicad batteries. If the batteries are trickle charged before they are fully discharged (usual practice I (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
 
  Re: Short term memory ablut sensor input???
 
(...) The program doesn't actually record in the Vectors array any information about where it saw an obstacle. It just records which direction the robot went and how far (according to the rotation sensor) during the last leg of the journey. Each (...) (26 years ago, 22-Sep-00, to lugnet.robotics.rcx)
 
  Re: Lego Mindstorms in Swedish television
 
(...) Or for every one, here is the official page from the University: (URL) and drool :) TGIF! /Tobbe (26 years ago, 22-Sep-00, to lugnet.loc.se, lugnet.general, lugnet.robotics, lugnet.technic)
 
  Re: Possible error in assembly guide.
 
Are you getting a good ground???...??? If it works.. then hey! RS232 is +10 to -10 but there is room for slop! +7 to -7 will work too!!!!!!! It just won't drive a cable to the max length of the RS232 spec. Most of the time though people just don't (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
 
  Possible error in assembly guide.
 
Near the end of the "interface/charger serial circuit" heading of the "Assembling The Handy Board" guide, it says measure the voltage of pin 6 of the MAX232, I did that and got -9.5 which is correct. Then I connected pin2 of j9 and pin6 of max232 so (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
 
  Re: Remote control
 
I have successfully trained my Sony Integrated Remote Commander RM-AV2000 (retails for $120) with the $20 remote from Lego. I have not tested training the remote from the IR tower, but I'm sure it would work. I'm also sure you could train any (...) (26 years ago, 22-Sep-00, to lugnet.robotics)
 
  RE: Remote control
 
(...) Hey good idea... Now I can justify a fancy learning universal remote to myself! m@ (26 years ago, 22-Sep-00, to lugnet.robotics)
 
  Remote control
 
Has any one tried using a universal remote on the RCX to see if it would work? If it did, $5 is a great improvement over $20! (26 years ago, 21-Sep-00, to lugnet.robotics)
 
  Re: Strong gear assemble?
 
Thanks for the help! After sending out the email, I thought of a way to do it (using a worm and a 40t gear ;), so now it lifts its self. Its interesting to watch as it rises though, because even though its semetricle, it goes up on first one leg, (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
 
  Re: Strong gear assemble?
 
I second the turntable suggestion. Triple black pin two beams to the molded-in mounting lugs and you can make a perfect space to worm-gear the outer ring. As an added bonus you get tons of mounting surface to put the rest of your big- rig (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
 
  Re: Advice on Rotation sensors and steering please.
 
Sorry. No I meant with correcting. My motors were matched pretty well, but without correction there was a large 2-3 foot error. Also the 500->15ft statement was an approximation of the actual numbers, I did this 3 months ago. Andy (26 years ago, 21-Sep-00, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR