 | | DDK and RDS on sale at Best Buy
|
|
I do not know if this sale is nation-wide or not, but in the Sunday 7/23 Best Buy sale flyer I saw that the store was discounting both RDS and DDK for this week (through 7/29). Yesterday evening I finally made it over there, and they did indeed have (...) (26 years ago, 26-Jul-00, to lugnet.robotics)
|
| |
 | | Re: Technic & robotics-compatible LEGO ZNAP clearance at TRU
|
|
"Miles Gentry" <gentrym@gte.net> wrote in message news:Fy128y.Gz6@lugnet.com... (...) while (...) not (...) Good (...) Get (...) on (...) "clearance" (...) I didn't find a flexible drive shaft in this set. Can anyone confirm that it should be (...) (26 years ago, 26-Jul-00, to lugnet.znap, lugnet.technic, lugnet.market.shopping, lugnet.robotics)
|
| |
 | | LEGO-DCP Sensor Adapter
|
|
I have been reading with interest the comments about our range of DCP sensors and their use with RCX. To help I thought we would post a few comments: Currently seven of our LogIT Microsense Sensors are supported by the LEGO-DCP adapter - sound, (...) (26 years ago, 26-Jul-00, to lugnet.robotics)
|
| |
 | | Re: RF Connection To RCX
|
|
One way to accomplish this is to use wireless serial devices. These RF devices allows one to hook up ANY serial device wireless. I have seen some listed on ebay for about $100+. The setup is as follows: PC--> serial transmitter serial receiver-->IR (...) (26 years ago, 26-Jul-00, to lugnet.robotics.rcx)
|
| |
 | | increased range of Infra Red
|
|
HI There Do You guys know how to increase the range of the infra red sensor to above 5 feet , if its an external circuit which I have to connect it does not matter , can some one send me the circuit so i can use the infra red sensor to sense a (...) (26 years ago, 25-Jul-00, to lugnet.robotics)
|
| |
 | | Re: RF Connection To RCX
|
|
Hi We just got into RCX. We have been using my Palm III and Visor to control the RCX. We have this great idea but need some help. We have an old Logitech Trackman remote control mouse. It uses RF. The idea is to some how convert the Serial output (...) (26 years ago, 26-Jul-00, to lugnet.robotics.rcx)
|
| |
 | | Re: RF Connection To RCX
|
|
Hi We just got into RCX. We have been using my Palm III and Visor to control the RCX. We have this great idea but need some help. We have an old Logitech Trackman remote control mouse. It uses RF. The idea is to some how convert the Serial output (...) (26 years ago, 26-Jul-00, to lugnet.robotics.rcx)
|
| |
 | | Re: light sensor problem?
|
|
(...) I supposed so, but only to get a "fast scaling"? (...) I can "rescale" those values by theoretical calculation and maintain >>7 or make the right conversion (0-100). Now I've done the right scaling (ready to commit), but I sincerely think that (...) (26 years ago, 25-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: Using CAN to Have More Than 3 Motors/Sensors
|
|
(...) Mark! This is great work! I am always impressed when someone goes beyond wishing for stuff that LEGO did not provide us with and then actually builds a working model. Your idea of a modular motor/input module is one of the great benefits of (...) (26 years ago, 25-Jul-00, to lugnet.robotics)
|
| |
 | | Re: Using CAN to Have More Than 3 Motors/Sensors
|
|
Hi Harri, The main board typically costs around $199US. It is available from Infineon distributors (Insight, Avnet, and Pioneer in the US), or directly from Phytec (www.phytec.com - look for their Kitcon167). Phytec also makes smaller footprint (...) (26 years ago, 25-Jul-00, to lugnet.robotics)
|