To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1731 (+10)
  Interactive C Sample Source
 
Is there any sample source avail on the web/ftp of IC routines. Like generic routines for object avoidance, navigation, light following, sound following stuff like that. (...) ___...___ Victor Clark Xerox Document & Data Services Xerox Corporation (...) (30 years ago, 21-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Sonar and the handyboard
 
Tom, I purchased 2 OEM kits (4 ranging units w/transducers) From this I had 3 bad ranging units. You'll notice a socketed chip on the PCB. I would suspect that this chip is suspect to failure. Anyways, in order to solve your problem, I would suggest (...) (30 years ago, 21-Mar-97, to lugnet.robotics.handyboard)
 
  SONARS GALORE!!!
 
For those who are interested..... I have recently developed a way of signalling 4 sonars from the HB using a logical switching circuit controlled by one ranging board and another board developed to switch which transducer is being signalled by the (...) (30 years ago, 21-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Sonar and the handyboard
 
Thanks, I followed Chuck M's advice, and disconnected the BINH, and the thing words, with 23" as the minimum distance. (...) I would have to possibly agree. I noticed in your earlier mail you have suggested putting a 330 ohm resistor between INIT (...) (30 years ago, 21-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Sonar and the handyboard
 
Ahh... This sounds right from when I had the same problem. I just forgot about the disconnecting of the BINH. Mainly because it was accidental at the time. Anyways, the point I wish to make is that you have a bad ranging unit. This symptom is (...) (30 years ago, 21-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Sonar and the handyboard
 
Tom, You mentioned that the INIT has the 330ohm. I'm pretty sure it's the BINH and NOT the INIT that should have the 330ohm. Reread Kents documentation. I don't think you would have damaged the unit in this short of time. Like I've mentioned on many (...) (30 years ago, 21-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Sonar and the handyboard
 
(...) I wouldn't think so. I am looking in Kents documentation, and sure enough, there is something about putting a resistor on BINH. Also something about putting a cap in C7 on the ranging board. I'll play with things tonight. (...) Good thinking (...) (30 years ago, 21-Mar-97, to lugnet.robotics.handyboard)
 
  Runtime Error 3
 
I'm kind of new to IC and I don't know how to deal with all the errors yet. I wrote a simple code to record sensor inputs every 15 minutes. This is the code I wrote: void main() { while(1) { int x[]; int s=analog(0); int f=0; s=x[f]; sleep(900.0); (...) (30 years ago, 21-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Sonar and the handyboard
 
Tom, I put the cap in too - never noticed much defference. It must just be for some minimal filtering of noise. I don't know how well you know Ben, but it sounds as though you will probably be fixing this one solo, eh? Do you have manuals? I'll look (...) (30 years ago, 21-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Runtime Error 3
 
Hi Peter, Well let me give it a shot, without actually downloading it to the Handy Board. It should go something like this: /* GLOBALS */ int num_sensors = /*put the number of analog sensor inputs you want*/ void main() { int sensors[num_sensors]; (...) (30 years ago, 22-Mar-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR