To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *13616 (+20)
  Re: X10 X-Cam
 
Accually, I saw a review on the X-10 camra on ZDtv, and it had a good point, the picture will flicker or be fuzzy if the antennia don't match up. KGB AgEnT #4 OUT AKA Clint Rutkas (URL) you check the web site first?: (URL) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: *BLUBOT*
 
(...) It's here: (URL) - Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: RIS 2.0 Ideas
 
Many excellent ideas have been suggested... I would most like to see Lego servos like what we have in remote control. These could use both an input and motor connection with appropriate firmware. <ICS> -- Did you check the web site first?: (URL) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: X10 X-Cam
 
(...) That has nothing to do with the camera, that has to do with the 2.4ghz video transmitter that X10 is including with the camera. The camera itself is *not* wireless and only outputs an NTSC signal through a male RCA connector mounted on the (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  [Off-Topic] Re: X10 X-Cam
 
(...) The amusing bit is that X10 has been doling out the possible uses for this thing one at a time. First it was the wireless camera, then "DVD Anywhere", now "MP3 Anywhere", when there is nothing different but which wires you plug into the back (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Droid Dev. Kit, reprise
 
Well, I've built a small "droid" from it now. And I have to admit, since it is a Technic kit, it was fun. It is only a little smarter than a Technic kit that only has a motor because of its programs (such as they are) and the light detector - but, (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: Droid Dev. Kit, reprise
 
(...) Well, A week or two back, when I was in Jacksonville, I had a nice conversation with a TRU store manager. He pulled up Mindstorms on his CRT and let me watch. Down at the bottom of the screen was a second something listed as 'RIS' (or (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  r/c servos
 
In response to the question about RC servos, I noted, while probing the signals on the I/O ports with a scope, that the motor power settings result in varying duty cycle square waves from 1:7 through 7:1 and finally full on as the parameter value (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: [Off-Topic] Re: X10 X-Cam
 
<SNIP> (...) Actually I believe the software that comes with the "MP3 Anywhere" is something similar to Ampapod (URL) allows you to use the X10 Mouse Remote to control Winamp. Ampapod is strictly 9x/NT though. (...) X10 is the king of marketing (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
I love the idea of controlling an R/C servo with the RCX, but I don't think it is possible with only software. On the other hand, a relatively simple circuit could be made to convert a duty cycle to a R/C servo signal. Is anyone out there interested (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
If the pwm is really being controlled by an 8 bit counter, that might be fine for the servos. The current rcx output has a cycle time of 8mS and uses 1mS increments. If those are the top 3 bits, then the resolution is 5 bits worth or 0.03mS. This (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) It is a software-based PWM. The topic of controlling a servo with the RCX has been discussed before. Generating the pulse stream for a servo would not be too difficult with the RCX, assuming you program the H8 directly using e.g. LegOS or (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) To get rid of the speculation here, the PWM is controlled by a programmable timer that the code in ROM configures to generate an interrupt every 1 ms. Output for each of 8 power levels is stored in a small table of waveforms, with the 1 ms (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: Droid Dev. Kit, reprise
 
Or could it be that new 2 in 2 out screen programmable (blue RCX) RIS? JT -----Original Message----- From: Ray Sanders [mailto:rsanders@gate.net] Sent: Friday, August 20, 1999 6:03 AM To: lego-robotics@crynwr.com Subject: Re: Droid Dev. Kit, reprise (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: X10 X-Cam
 
Don't buy the X-10 system expecting to use it for robotics. Those 2.4Ghz transmitters are directional and therefore are not well suited for the robotics application. Go to Best Buy or shopping.com etc. and buy a 900Mhz transmitter/receiver (actually (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  I/R Strobe/Omnidirectional sender/receiver
 
Greetings all, Looking at some of the new posts like the conductor/piano player has got me to thinking about the multiple RCX interacting scenario. The biggest inefficiency to start with is having to direct the entire RCX toward the other one, have (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: Droid Dev. Kit, reprise
 
(...) They'll probably do what LEGO wants them to do. LEGO appears to be fairly inflexible and uncreative and will probably stick to their normal policy. LEGO's normal policy seems to be to tell the store it has been discontinued and allow the store (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) If all you need to do is generate a pulse of a certain length, why can't you do something like this? Sleep(1); // synchronize with the centisecond timer Fwd(OUT_A, 7); Sleep(1); // 1/100 of a second Off(OUT_A); Sleep(2); // 2/100 of a second (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) I can't understand this. Can you correct your grammar so it is clear what you're saying the average servo needs? - Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) The answer is pretty simple, actually. In order to control a servo, you need to use pulses whose lengths are on the order of 1-2 ms. The more steps you get in that range, the more servo positions you can use. NQC can't produce pulses as short (...) (27 years ago, 20-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR