 | | Re: LNP Repost
|
|
(...) My only thoughts are that not everybody will need or want the generality of port support in the protocol. I would suggest reordering the first four bytes, moving the payload length up toward the front, and defining it to explicitly include the (...) (27 years ago, 28-Jul-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) (extra removed) (...) Don't forget, at the actuation end, a pneumatic-based motor should be liquid compatible, something the electric motors have a hard time with. Also, you can run the air lines quite far, so long as you are willing to accept (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
Jonathan Knudsen <lego-robotics@crynwr.com> wrote in message news:3.0.5.32.199907...net.com... (...) You might try a trim pot in place of the 2.2K and set the room temperature to be the correct value. You could later determine the trim pot value (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Laser Pointers
|
|
(...) Laser pointers were legal in the uk but to my knowledge have been banned because kids were misusing them, in one incident a Bus nearly crashed and the driver was in hospital for a while after a school kid bounced the laser beam of the rear (...) (27 years ago, 29-Jul-99, to lugnet.robotics.rcx)
|
| |
 | | Re: rcxhttpd?
|
|
I love the idea, I think it would be great to see hundreds of little bots whizzing round my house comunicating with each other. Its a bit like teaching your dog to fetch the morning mail. Alan Bell. (...) (27 years ago, 29-Jul-99, to lugnet.robotics.rcx)
|
| |
 | | Toronto lego robot challenge
|
|
Calum and I were talking about this, a copy is also being sent to lugnet.*.*.toronto ---...--- Forwarded message ---...--- Date: Wed, 28 Jul 1999 21:26:00 -0400 From: Calum Thomas Tsang <tsangc@ecf.toronto.edu> Subject: TORONTO: Mindstorms (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Hi, I was just wondering where i could find the small pumps that are used to make the compressors. I would like to find it as a seperate piece so that i do not have to buy a whole box. I got a lot of pneumatics with the set 8462 Tow Truck (available (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Hi Nicolas, You will find the parts in the Offical Lego web(www.lego.com) site thru the catalog link. select the service button and then the technic button. This will show you a list of available parts thru the Shop at home service. the part (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Serial line output
|
|
Just started to learn how to use my new HB. In going through the IC manual I could not find any routines for writing to the serial port. Does anybody have a good example on how to write "hello world" to the serial port, and have the attached (...) (27 years ago, 29-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) You know, I think I'm starting to get nervous about this 1.5 business. Let's say they do happen to ship a 1.0->1.5 software compatability upgrade. The first question that comes to my mind is: Is the upgrade reversible or irreversible? Any why (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|