 | | (no subject)
|
|
Hi, I get this message attached to some of you guys' mail. Does anyone know what it means? This message contains non-ASCII text, which can only be displayed properly if you are running X11. What follows may be partially unreadable, but the English (...) (30 years ago, 5-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: SPI code
|
|
(...) Just to be clear: the code I have promised is 1200 asynchronous serial output from the HB (from a pin other than its built-in RS-232 out :-), *not* SPI code. Mike is correct in stating the place for info is the 6811 "pink book." See the HB (...) (30 years ago, 5-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | baud rates
|
|
Hi all, I have a question concerning baud rates and the SCI port. I looked in one of the pink books and found the maximum baud rate it shows is 131.072k baud. I need it to be 250k baud. I also noticed that the baud rate is dependant on the crystal (...) (30 years ago, 5-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | infrared communication
|
|
Hello, I'm trying to find information on how to implement infrared communication between my PC and my RugWarrior (a 68HC11 board). I want is to use the serial interface of the board (another port would be fine btw), which is normally connected via a (...) (30 years ago, 5-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Polyswitch Fuse
|
|
I looked up the part in DigiKey Catalog. Is there a reason for choosing a fuse rated at 2.5A with a trip of 5.0A? (30 years ago, 6-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | more downloading
|
|
Hi everyone, I posted a message a day or two ago about a downloading problem I am having with my HB. I have gotten my hands on a copy of hbdl.exe and it too fails to download pcode_hb.s19. I believe that I am following all instructions properly. (...) (30 years ago, 6-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polyswitch Fuse
|
|
Not a real systematic one -- that seemed to be enough to let motors blast away, but stop real damage from happening if the nicad pack got shorted out. remember, shorting nicads is a real hazard - 50 to 100 amps -- could almost start a car. -fred (...) (30 years ago, 6-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: more downloading
|
|
Hi Dave, can you try the DLM.EXE (not hbdl) program off the software resources web page? you will have to use the "-256" flag because it defaults to -512 for the e1 version of the 6811 which is probably not what you have. also, if you have windows (...) (30 years ago, 6-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Blown Board!
|
|
Hello! Boy do I feel silly! I'm captain of a robotics team here at Washington University and I ran into a problem tonight while soldering up my board. We've been building the board from the kit and all has been well until now. My assistant and I (...) (30 years ago, 6-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | handyboard stuff
|
|
I,ve just received my Handyboard pcbs from Douglas Electronics and they were very quick in getting them over to me in the UK. I,ve just about got them chiped up and will be testing today. Books: In looking around for relevant books on the 68HC11 I (...) (30 years ago, 6-Dec-96, to lugnet.robotics.handyboard)
|