 | | Mounting the handyboard
|
|
I am using the handyboard from Gleason Research. It works very well. Only problem is there is no obvious way to mount it rigidly into a robot. No mounting holes or brackets. What have others done? -Matt Grob (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Mounting the handyboard
|
|
You usually take a glue gun and glue some kind of mounting device (in my case legos). to the red plastic part. -peter (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Mounting the handyboard
|
|
I've used velcro. You can buy long rolls of it at Walmart I think. ---...--- (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: RCX Challenge
|
|
(...) Something is missing, you know... I'm just gona throw up some ideas (and sorry the English): First you need to publicize it frequently. You also need to publicize who are the current contestants, the status of the them while the contest runs, (...) (28 years ago, 4-Apr-99, to lugnet.robotics)
|
| |
 | | Re: Data Sheets
|
|
(...) for (...) 32k (...) What I meant to say was compiled. sorry. (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Mounting the handyboard
|
|
Matt Grob Matt Grob (...) True, but you can make a sort of rigid cradle for it out of angle beams with tiny pulleys with "tires" around them at each corner: O O \ / \___...___/ side view |---...---| = | | = <--small pulleys with "tires" | | | | | | (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Download program code from the RCX
|
|
(...) You are SOL. The standard firmware does not allow you to retrieve data from the program area of the RCX. No amount of hacking will fix things. Modified firmware could help you, but you can't download new firmware without destroying the current (...) (28 years ago, 5-Apr-99, to lugnet.robotics)
|
| |
 | | mailing list archive site
|
|
Hello all - I have created a website to archive the traffic generated on the Handy Board mailing list. It is currently not updating in real-time, but will start updating automatically as soon as Fred gets back and adds my second address to the (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Even more remote controls
|
|
(...) You probably won't find a preprogrammed remote that works with the RCX. Most of these use a 11 or 14 bit command (this for some remotes can vary between 1 and 64 bits) where as the rcx uses 8 bits with start and stop bits just as on a PC (...) (28 years ago, 5-Apr-99, to lugnet.robotics)
|
| |
 | | Re: IR transmission from legOS?
|
|
Hi Kay, essentially, Ralph already asked all the right questions. You have about three seconds after the last keystroke to press the view button, or the IR tower will power down. If problems persist, please mail me your compiled executable (...) (28 years ago, 5-Apr-99, to lugnet.robotics)
|
| |
 | | Using both Sharp GP2D02 and Polaroid 6500 -Reply
|
|
I posted a message asking IF any one had timing issues using the 6500 and the GP2D02 but never received a response. My concern is running the sonar, IR and encoder routines concurently as seperate processes. Will IC be able to keep up??? Some (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Obstacles avoiding -Reply
|
|
The idea behind a reactive (behavior based) architecture of a Rug Warrior robot is essentially stateless. You may want to add some kind of schedule or activation layer (process ) that enables the low level behaviors based on some type of state or (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Using both Sharp GP2D02 and Polaroid 6500 -Reply
|
|
I have a Rug Warrior fitted with the Polaroid 6500 sonar, and a Handy Board that uses the GP2D02 sensor. Both applications use a servo for aiming. On the Handy Board site, the libraries have been altered to support the GP2D02, but I did my own (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Walker
|
|
Go here, and try not to drool. There are two working chicken walkers, one that can actually toe out the legs to turn. (URL) (28 years ago, 5-Apr-99, to lugnet.robotics)
|
| |
 | | Config register and E9/E1 processor
|
|
Are there any tools for programming the E9/E1 config registers from Linux or NT? I don't have a DOS or Win95 machine handy at the moment, and I remember that the download program for the hc11E processors must be a little different. I can't get DLM (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | GCC: Status
|
|
It looks like at least three of us were playing with gcc-2.8.1 over the weekend. The GCC Miniboard library is now mostly ported over to the Handyboard, and the ICC11 LCD routines are almost done being ported over. I couldn't test out the motor (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: mailing list archive site
|
|
(...) This is a great idea, Jeff! From all of us, thanks. Duncan (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Quick troubleshooting help please!!!!
|
|
Hey, Two weeks before we present our project and the HandyBoard got fried!!! Ahhh! Oh well, hopefully someone can help us identify the problem. The board seems to work fine as long as its getting power through the RS-232 connection. Once this is (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Counting pulses
|
|
Could any one point me in the right direction for information on calculating frequency using the handyboard, Thanks Keith (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Quick troubleshooting help please!!!!
|
|
Did you destroy the battery pack? There is an embedded temperature fuse that will blow if you try to charge it too fast or accidently short the battery. With no power applied have a look at the voltage on the battery terminals (you can get to them (...) (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)
|