 | | Re: HB Memory
|
|
Stef, The HB comes with a 32K ram chip addressed at $8000 and above. A fair amount of this space is taken up with the Pcode interpreter if you run Interactive C, but there is still lots of room left for programs. Good luck, Gary Livick (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Help with pointers
|
|
(...) When you do pointer arithmatic, you work in increments of what the pointer points to. So if you have a pointer to an int, as in the above example, when you add one to it, you actually make it point to the next int, not the next byte or word. (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
I have not tried pneumatics yet. I know where I will look when I try them out. This is another neat clean working device. Nice work! Bob Fay rfay@we.mediaone.net The Shop (URL) Hempel <rhempel@bmts.com> wrote in message (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Robot Mapping
|
|
Hello, I am working on an autonomous mobile robot. Which has a sonar and infared sensor incorporated into it. Right now it can avoid objects, by sensing it and backing up and turning. I want my robot to take the information from the sensors and map (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) Heck, I'd love to try some pneumatics, but you can't get a storage tank anywhere these days can you? All of the cool Technic kits are discontinued, no subs, (and while I'm whining) no shuttles, no tracked vehicles, only Throwbots and (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | RE: Sharp GP2D02
|
|
Scott, The reason I wrote mine the way I did was so that I could avoid disabling interrupts for long periods of time. If you don't care about timer interrupts or things like wheel encoders, either program should work fine. My program uses digital 15 (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Robot Mapping
|
|
I would also like to know about this. please cc any info to me too. =) chen (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) 8462 comes with two of them, and is available from Lego S@H. I'd like to see reissues of the construction vehicles as well. alex -- Did you check the web site first?: (URL) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Help with pointers
|
|
(...) Actually, in 'normal C', to be completely correct you would cast the pointer conversion to show that you really knew what you were doing, like this: p = (char *) &x; Unfortunately, neither the free ware IC nor IC 3.2 support this. Here is (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: How do you convert light sensor data to bmp image
|
|
Alex: Downloaded the netphm files from your site. Your right, it was alot easier. Now all I have to do is build my scanner. Thank you for your help Patrick McLean :) Alex Wetmore wrote in message <922292440.681002@phred.org>... (...) image. (...) (28 years ago, 26-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | RE: Robot Mapping
|
|
Check this reference out: "Autonomous Agent Map Construction in Unknown Enclosed Environments", Keith L. Doty and Steven L. Seed, Machine Intelligence Lab, DEE, University of Florida, Gainesville, FL and Chapter 10 of: "Sensors for Mobile Robots, (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Robot Mapping
|
|
(...) I've been thinking about this too. The problem as I see it is that without some shaft encoders on the wheels, your robot doesn't really know how far it's moved, and therefore where it is in the map. If you power on the forward motor for 2 (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | [Fwd: Robot Mapping]
|
|
-- ___...___ Jonathan Pennington -Anthropologist/Geologist -Linux User and Advocate -Bart Simpson Sympathizer Email at jwp(at)awod.com ___...___ (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: [Fwd: Robot Mapping]
|
|
(...) Heck, that sounds pretty easy. As long as you know where you start from and you use a cartesian or polar form of V=vsub0 + a*t integrated over time, and you are either working in a vacuum or at such low velocities that c sub d is negligible, (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
Dennis, Thanks for your encouragement. The angle sensor connected straight to the RCX is non-linear because it is in series with another resistor located inside the RCX. During a sense operation, the RCX drives the sensor input from a 10K resistor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: [Fwd: Robot Mapping]
|
|
-->Heck, that sounds pretty easy. As long as you know where you start from and you use a cartesian or -->polar form of V=vsub0 + a*t integrated over time, and you are either working in a vacuum or at such low -->velocities that c sub d is (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
(...) As for the diode vs FET, the package used for surface mount is going to be the same so there is no size penalty. The only thing I might change is the regulator, on battery powered equipment I would tend to a DC to DC converter like Motorola's (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
What about a real time circuit that routed the output power to one of eight output ports depending on the PWM. That way it only takes one output port on the RCX and up to three (out of 24) motors could be running at the same time. (...) like (...) (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Joel Shafer ----- Date: Thu, 25 Mar 1999 13:43:33 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller What about a real time circuit that routed the output power to one of eight output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors (fwd)
|
|
----- Forwarded message from Pete Sevcik ----- Date: Thu, 25 Mar 1999 21:00:13 -0600 From: Pete Sevcik <sevcik@flash.net> Subject: Re: 3-wire converter for homebrew sensors The angle sensor connected straight to the RCX is non-linear because it is (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|