 | | Battery voltage available within NQC?
|
|
Last night I went out and bought six C cell nicads and wired them up as a power supply for my robot. What I'm wondering is this: is there some way to programmatically obtain the battery voltage, so I could make a decision based on a voltage (...) (28 years ago, 11-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Ultimate Starter Sets / Add-Ons for Mindstorm? Reprise
|
|
Mindstrom fans seem to go through a lot of grief finding or ordering just the right set of parts. I recently read a memo on the 'net lamenting some of the shortcomings of the Lego system: it is difficult to build certain structures, things must fit (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Battery voltage available within NQC?
|
|
(...) There's a bytecode (0x30) that instructs the RCX to send the battery voltage as a response over the IR. That's what NQC and Mindstorms use to read the battery voltage. I don't think this opcode has any effect within a program, or at best it (...) (28 years ago, 12-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Looking for Mac prog environment
|
|
(...) (URL) reply to: dbaum at enteract dot com (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Battery voltage available within NQC?
|
|
(...) If you REALLY wanted to do this, you could use the bytecode to broadcast the battery information to the IR tower and have a service running on the PC which would recieve the battery message and then send an appropriate message back to the RCX. (...) (28 years ago, 12-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: More outputs, thinking outside of the box...
|
|
To get more electrical about it, how about making a voltage gate for the third output, that according to what voltage you set the third output to (between 1 to 9 volts), it switches on different sets of motors? Also, polarity changes could trigger (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Anybody have Peter Pletcher's TclRCX??
|
|
Laurent is very busy with his new child and hasn't made any progress on TclRCX and he never got together with Peter Pletcher. Peter Pletcher's web site is no longer online. I tried sending email to Peter, but have gotten no response. Does anybody (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Servo Expansion Board
|
|
Hi all, I have the Handy Board running fairly well, although I havn't tested ports, etc. Question. I have the expansion board, and when I try to run the init_servo (not exact) command, the board locks up. Anyone see this problem before? Thank you, (...) (28 years ago, 12-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Sensors
|
|
hi i'm trying to find a cheap and reliable infra-red digital sensor with a sensing range of around 0-30cm. does anyone have any recommendations? are there any online stores that sell a wide variety of such sensors? btw, the sharp GP2D05/02 sensors (...) (28 years ago, 12-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Polarity switch Question
|
|
Does anybody know if the polarity switch has a neutral center position? In other words, does the switch go: forward<->off<-->reverse Please share with the group... Cheers, Ralph Hempel - P.Eng ---...--- A picture is worth a thousand words, but very (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Polarity switch Question
|
|
# From: rhempel@bmts.com # Sent: 12 March 1999 14:17 # To: lego-robotics@crynwr.com # Subject: Polarity switch Question # ---...--- # Does anybody know if the polarity switch # has a neutral center position? In other words, # does the switch go: # # (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | (no subject)
|
|
Hi, have any of you guys tried wall following with 4 ir proximity detectors? I'm having trouble getting mine to work properly. I think the problem is with my program. I'll attach it in my next letter, hope someone could help. Thanks. F. Samonte (28 years ago, 12-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polarity switch Question
|
|
(...) Yes. Moreover, rather than just toggle it, you can turn its axis and have: forward <-> off <-> reverse <-> off <-> forward <-> off <-> reverse <-> ... Hao-yang Wang (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Communicating with RCX native serial port
|
|
I have been trying for the last week to get my RCX to respond to serial commands i am a little confused. I think i understand most of the header packet stuff but here's where im stuck... you send 0x55 0xff 0x00 as the header... I am sending this as (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Watch Dog Timer on legOs
|
|
Anyone have any experience using Interrupts for the h8300? I want to add a watch-dog time routine to legOs. I was hoping someone could nudge me in the right direction?? I just need to understand how to access the system clock? Brian -- Did you check (...) (28 years ago, 13-Mar-99, to lugnet.robotics)
|
| |
 | | LEGO 9V battery box as project container
|
|
Well, I've been looking for a suitable container for my LEGO robotic electronics projects, and I think I've finally found it. I got tired of dremeling out the inside of bricks, especially since some of my projects are bigger than the biggest brick. (...) (28 years ago, 13-Mar-99, to lugnet.robotics)
|
| |
 | | Re: LEGO 9V battery box as project container
|
|
(...) Wow, I assumed the battery box was the one that comes with the 3735 motor kit. It's 4x14 by about 1 1/2" tall. This must use a 9V battery instead of 6 AA cells. (...) And THAT price can't be beat for getting another power connector block too! (...) (28 years ago, 13-Mar-99, to lugnet.robotics)
|
| |
 | | Computer controlled trains
|
|
Has anyone else controlled a train layout with Mindstorms or Decta controll lab? SteveB www.PNLTC.org (28 years ago, 13-Mar-99, to lugnet.robotics)
|
| |
 | | Re: How big is our community?
|
|
it's about 500 people. fred In your message you said: (...) (28 years ago, 13-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | navigation
|
|
Hi. I'm a bit new to this, and have a question. Could someone point me in the right direction (no pun intended) on where to find a good starting point on robotic navigation? I have played around with bump detection but that is not exactly what I am (...) (28 years ago, 13-Mar-99, to lugnet.robotics)
|