 | | 2x3 trapezoid
|
|
Hello I have just got myself set up with MLCAD and I am drawing up all the MOCs that I have been unable to break down due to not wishing to forget how to build them but I have run into a problem which I hope this is the right place to come for an (...) (23 years ago, 17-Apr-01, to lugnet.cad.mlcad)
|
| |
| | Re: Printing parts-list
|
|
Thank you for the bug report - I will check that today and fix it for V2.00 Michael "Maico Arts" <maico@m-arts.demon.nl> wrote in message news:GB4p7x.2Ep@lugnet.com... (...) (23 years ago, 4-Apr-01, to lugnet.cad.mlcad)
|
| |
| | Printing parts-list
|
|
Hello (Michael?) I think I have found a bug in mlcad when printing the partslist. I am making inventory lists ofall my technic sets. I have build all sets I have, put them back in the boxes and added the extra parts. Using ML Cad I am making (...) (23 years ago, 1-Apr-01, to lugnet.cad.mlcad)
|
| |
| | Re: Printing problems in MLCAD
|
|
(...) I had essentially the same problem and found the following fix; Select 'Printer Setup' in MLCAD Select 'Properties' Check 'Scale to Fit' Check 'Scale to fit paper in printer' Then about three 'OKs' I don't know about others but this seems to (...) (24 years ago, 25-Mar-01, to lugnet.cad.mlcad)
|
| |
| | Re: Rotation trouble
|
|
Hey, There should be some buttons with arrows going around axes. These control the rotation of an element around the x, y, and z axes. The degree of rotation is determined by the grid icon. You can also edit the amount of rotation by going to (...) (24 years ago, 24-Mar-01, to lugnet.cad.mlcad)
|
| |
| | Re: Rotation trouble
|
|
Hey Dug, I have had some difficulty with that at times as well. One way I began to over come the problem was to open the rotation dialog bod and go to the bottom text window (you have to click the radio button to enable it). And enter "1 0 0 0 1 0 0 (...) (24 years ago, 24-Mar-01, to lugnet.cad.mlcad)
|
| |
| | Rotation trouble
|
|
Hi all, I'm pretty much new to MLcad, although I'm not quite new to the world of CAD. I had some trouble after rotating a part at 45deg. After that I couldn't get the rotation angle back to 90.... Pieces were rotating all over the place, but not at (...) (24 years ago, 24-Mar-01, to lugnet.cad.mlcad)
|
| |
| | Re: Use of cursor keys in MLCad views
|
|
"Ryan Farrington" <ryanjf@ifriendly.com> wrote in message news:00bb01c0b234$6b...dly.com... (...) No, I didn't - thanks for letting me know. It's still a bit of a pain as my home and end keys are in the far top right of the keyboard and next to each (...) (24 years ago, 22-Mar-01, to lugnet.cad.mlcad)
|
| |
| | Re: Use of cursor keys in MLCad views
|
|
(...) a (...) maybe (...) the (...) [snip] Home and End move pieces up and down in the Y axis. (I don't know if you knew that...) Regards, --Ryan (24 years ago, 21-Mar-01, to lugnet.cad.mlcad)
|
| |
| | Use of cursor keys in MLCad views
|
|
Maybe I have something setup incorrectly here, or maybe I'm asking for something that is in the works for v2, but I find it a pain to use my "mouse" (it's a flat pad on a laptop PC and not very easy to use) to move parts in the 3 views so I tend to (...) (24 years ago, 21-Mar-01, to lugnet.cad.mlcad)
|
