 | | Re: Voting page for 9906
|
|
Jeff Stembel <Dragonelf1@aol.com> wrote in message news:FFuFFw.Cr0@lugnet.com... (...) The insertion point is the center of the cylinders. This makes it much easier to rotate on the z axis, and to rotate on the x axis then place in its vertical (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
(...) Well, in LDLite, it looks like there is a faded crosswalk when shading is turned on. It looks really bad, IMO. (...) Oops, my bad. Yes, I meant 609p01. Thanks for changing the color. Now it'll match the current road plates. Talkin' 'bout the (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Spline-generator
|
|
Hi, After experimenting a bit with the current tools for creating flexible parts I had a lot of problems to place and orientate the hoses using Bezier-curves. I've looked around a bit and found some examples using multi-point splines. Main different (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Voting page for 9906
|
|
(...) i would just like to say that i am prepared to admit that the roadplate parts probobly were not redy for voting on but on the 32 x 32 raised with ramp the mistakes on the corners and also the line in the pit were all honest mistakes. (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
(...) i promise to fix the pit extra line asap.also about the corners... i can fix those as well. thanks for pointing out the mistake. (...) my mistake. i thought i could make this by changing the color of the grey bits on the dashed roadplate to (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
(...) OK. (...) That sounds cool! I've never used LDAO to edit anything before. Let me give it a try before I bug you with it. Thanks, Adam (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
(...) [Snip] (...) If you use LDAO, open the file in the Editor, select the entire file, then click Edit | Move Exact. Type the distance to move in the Y box. Click OK. Save the file. If you don't LDao, I can do the edit for you... Steve (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
Jeff Stembel <Dragonelf1@aol.com> wrote in message news:FFuFFw.Cr0@lugnet.com... (...) hinged (...) Yes, actually that wouldn't be a bad idea, but it would take me way too much time. When I originally submitted these doors back in Oct/Nov, they were (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: are idea book models going to be accepted into the omr?
|
|
(...) yeah. there were the blacktron II and mtron mega model set instructions... (25 years ago, 2-Aug-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: are idea book models going to be accepted into the omr?
|
|
Tim Courtney <tim@zacktron.com> wrote in message news:4.2.0.58.199908...omm.com... (...) Actually, they do have set numbers. Go to the Pause DB and search for "Idea Book" to see for yourself. I think they should be included for many of the same (...) (25 years ago, 2-Aug-99, to lugnet.cad.dev.org.ldraw)
|
