 | | ERROR in lcad9903 update
|
|
Sorry folks, I made a mistake in update 9903. Piece 2429, the 1x2 hinge plate, was overwritten by another part. For an immediate fix, you can download and install this quick fix; (URL) it just like any other update. It contains: 146.dat a ~Moved to (...) (25 years ago, 20-May-99, to lugnet.cad.dev)
|
| |
| | Re: Part 2429
|
|
(...) Joshua's simple typo, but my QA error. I coulda swore I went through all the potential number changes and checked each one for conflicts with existing pieces. Now that the real story is known, I will endeavor to correct the problem ASAP. -- (...) (25 years ago, 20-May-99, to lugnet.cad.dev, lugnet.off-topic.fun)
|
| |
| | Re: Voting Comments
|
|
Steve Bliss skrev i meddelandet <3741a8a1.20817582@l...et.com>... (...) Is that safe for transparent pieces? I toyed a little with re-sorting some parts to 'outside-in' instead of 'inside-out' to make the drawing faster (minimize overdraw), but then (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Spheres in LDLite [DAT]
|
|
I just noticed that when I view a sphere in LDLite in a front, side, or top view, half of the edge line is not drawn. This is true in standard or wireframe mode. In LDraw they are all drawn. I did a little investigation, and it appears to be related (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Part 2429
|
|
In lugnet.off-topic.fun, Duane Hess writes: DOH! Let's try this again. (...) (25 years ago, 19-May-99, to lugnet.cad.dev, lugnet.off-topic.fun)
|
| |
| | Re: new part description changes?
|
|
(...) The term "bogie" refers to the _swivelling_ function of a wheelset. I can't see what about 2871 marks it with that function. The addition of a bogie plate to the motor would give a bogie function, but that doesn't have much to do with 2871. (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Part 2429
|
|
(...) ^^^...^^^ (...) Don't be so hard on yourself. Wishing yourself out of existance is not the answer. :-) duane (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Piece needed to finish MOC Naboo Fighter
|
|
(...) I thought I posted a mockup of this piece, but I can't find any such posting. Hmmm. I'll work on it. I promise. Steve (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: new part description changes?
|
|
(...) The new part, 32059, doesn't go with the other parts in the Wedge category. All of the wedges feature at least one side which is angled across 1x3 studs. 32059 has sides angled across 1x2 studs. There are several types of angle-sided plates in (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
(...) That's a really great idea! It's obvious you're pretty experienced with LDraw. I'll do the changes when I get home. Fredrik (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Comments
|
|
(...) You are indeed correct, yes. Thanks a lot. I took the time to "brush up" the surface around the axle holes as well. I believe the current solution is a better one; I no longer use partially overlapping 2-4rings to cover the surface. The part (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Page [DAT]
|
|
I've noticed an error in part #30250, that was named "Brick 2 x 4 x 3 Notched with Side 5 x 4 Plate" during the vote. Four box5.dat primitives have been used to form "friction rims" at the under/inside of the part, but they are not properly rotated. (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Part Name Question
|
|
jonathan wilson wrote in message ... (...) No, no more "space" required I think. A generic category like "bar" would be nicer. But I admit that there is no simple definition for "bar" category for this part like "space gun 1x8" Selçuk (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: new part description changes?
|
|
Terry K wrote in message <37422782.12164362@l...et.com>... (...) Any (...) Looks nice to me, too. (...) Corners", (...) I strongly agree. By the way, I don't think the part that Steve pointed out should be considered as "w/o corners" variety. It is (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Piece needed to finish MOC Naboo Fighter
|
|
(...) Yes, someone *please* do this. It has been on my wish list for ages. One of those "I can't believe it hasn't been done" pieces. (1) -- Terry K -- 1. FYI, the piece does exist in Lutz's L2P. (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Part 2429
|
|
(...) No, you didn't miss something. I missed something. I thought I had carefully checked all number changes for conflicts with existing parts, but obviously, I didn't catch that one. 2429 was the Hinge Plate, released in the original LDraw (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Part Name Question
|
|
(...) i say space (...) space gun 1 x 8 dsounds good. (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: [makelist] mklist v1.2
|
|
(...) Consider it done. -- Terry K -- (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: new part description changes?
|
|
(...) I favor this one as well. (...) I agree. And as Steve pointed out, there is precedence for "without Corners", whereas there is none for "Tapered". (...) Cow-like, I will follow this herd and agree. (...) Beat me to it! I was just going to say (...) (25 years ago, 19-May-99, to lugnet.cad.dev)
|
| |
| | Re: Voting Page
|
|
(...) Fix 'em. They all passed. -- Terry K -- (25 years ago, 19-May-99, to lugnet.cad.dev)
|
