 | | Re: BrickDraw3D development announcement
|
|
(...) It's easy to miss OpenGL errors. Are you sure it's the glBegin causing the error, and not some previous command? Remember that successful commands don't clear the GL error state. Did you check for an error right before calling glBegin? (...) (23 years ago, 6-Feb-02, to lugnet.cad.dev)
|
| |
| | Re: LCD - LEGO Connection Database - Proposal
|
|
You're forgetting one important connection! The connection between the tire and the road surface. What about that? -Mike (...) (23 years ago, 6-Feb-02, to lugnet.cad.dev)
|
| |
| | Re: need help w/ name (minifig legs from set #4817)
|
|
(...) Peeron calls this one "Minifig Hips and Legs Assembly with Red and Brown on Legs and Belt Pattern" ("(URL) (Steve, Chris: I'll also need a pattern number (...) Steve, Chris, I was thinking of using these: 970p4b Minifig Hips - Leather (...) (23 years ago, 5-Feb-02, to lugnet.cad.dev)
|
| |
| | Re: BrickDraw3D development announcement
|
|
(...) Four cases that come to mind 1. as you say existing begin 2. command other than vert,color,index,nor...Co,evalPo, arrayEl,material,edg...allList(s) & Some '_EXT's if storable in begin end. Keep anything else after or before as needed. 3. Some (...) (23 years ago, 5-Feb-02, to lugnet.cad.dev)
|
| |
| | need help w/ name (minifig legs from set #4817)
|
|
I've gotten several of the minifig from set # 4817 ("(URL) I intend to encode the printed hips-and-legs for this minifig into LDraw. But, I need some help coming up with the name for the printing of this piece. In LDraw, I'll actually be encoding (...) (23 years ago, 5-Feb-02, to lugnet.cad.dev, lugnet.castle, lugnet.build.minifigs)
|
| |
| | Re: Name this Jack Stone part
|
|
(...) That pin in the middle, appears to add significantly to avoid unintentional disconnect. The tallness of the pillar with respect to the shortness of a typical stud would cause it to be much less stable without the pin. The Jack Stone parts (...) (23 years ago, 5-Feb-02, to lugnet.cad.dev)
|
| |
| | Re: Name this Jack Stone part
|
|
(...) Hmm.... Brick 10 x 10 with Corner Extensions Brick 10 x 10 with Corner Support Extensions Brick 12 x 12 without Sides Jack Stone BaseBrick 10 x 10 Whichever dimension (10x10 or 12x12) is used in the part, the *other* dimension should be (...) (23 years ago, 5-Feb-02, to lugnet.cad.dev)
|
| |
| | Re: Stud logos in fan apps
|
|
"Dave Schuler" <orrex@excite.com> wrote in message news:Gr2Kr7.IGE@lugnet.com... (...) Well, yes. The loose-knit community which is the 'governing body' of the parts updates and libraries was called LCAD, or at least, the parts updates themselves (...) (23 years ago, 5-Feb-02, to lugnet.cad.dev)
|
| |
| | Re: Stud logos in fan apps
|
|
(...) Figures--I spent all last week debunking conspiracy myths, and it turns out I'm the victim of one! I'll be watching you... Out of curiosity, was it *ever* "officially" called LCad? Dave! (23 years ago, 5-Feb-02, to lugnet.cad.dev)
|
| |
| | Re: Stud logos in fan apps
|
|
"Dave Schuler" <orrex@excite.com> wrote in message news:Gr2HCq.9BC@lugnet.com... (...) You know we did it just to upset your site ;-) Actually, its someting Steve and I chatted about for some time. I started considering this, and discussed it with (...) (23 years ago, 5-Feb-02, to lugnet.cad.dev)
|
