 | | Re: castle minifig torsos?
|
|
(...) <set:6009> (...) It is named precisely that - and is available as an unofficial part on the Parts Tracker at (URL) just added the missing subpart s/973p40a (...) There ia a lot of fine detail on this one - I'll see what I can do. (...) (...) (23 years ago, 20-Oct-01, to lugnet.cad.dev)
|
| |
| | castle minifig torsos?
|
|
Hello all, I am finally getting around to finishing putting my Trojan horse model into LDraw -- I started LEditing it at least five years ago (really, it's a simple model; I've just been ignoring it) -- and I am almost done. All that's left to do is (...) (23 years ago, 20-Oct-01, to lugnet.cad.dev)
|
| |
| | Re: LDraw History - here's one for the old timers in the group....
|
|
(...) Some more dates: September, 1999 Datsville (at first LCADville) was born. Although Datsville never went as far as I (and others) would like to have seen it go, I think it made an important contribution to seeing what could be done with LCAD. (...) (23 years ago, 19-Oct-01, to lugnet.cad.dev.org.ldraw, lugnet.cad, lugnet.cad.dev, lugnet.people)
|
| |
| | Re: Parts Tracker - Using L3P-check to scan submitted files
|
|
(...) [snip] (...) [snip] (...) No, they should be fine. If you use a line like 0 END ROTATE (upper- or lower-case), that would cause the error message. Maybe we should have specified (back in the day, too late now) that meta-commands all have to (...) (23 years ago, 19-Oct-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Net generator spreadsheet
|
|
If you want to model a curved net as used in some sets try my net generator. Take a look at www.sayce-jones.co.u...go\cad\net Right click on the small image to download the spreadsheet. Modify the map worksheet to generate the net shape you want and (...) (23 years ago, 19-Oct-01, to lugnet.cad.dev)
|
| |
| | Re: "All zeros" warning (Was: Parts Tracker Activity Page)
|
|
(...) Yes, I believe they are. I haven't rechecked lately to see if anything has changed. If I get a chance in the next few days I will recheck it. (...) I understand and agree. I will cease making any comments on them. (...) really? ok. (...) Paul (23 years ago, 18-Oct-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Parts Tracker - Using L3P-check to scan submitted files
|
|
(...) Looks good. (...) I have used the phrase "0 end of subpart", "0 end of file", etc in some of the parts I have made. Will these get rejected? I usually always try to keep them lowercase. (...) I'm not sure about this one. I feel that new parts (...) (23 years ago, 18-Oct-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Parts Tracker - Using L3P-check to scan submitted files
|
|
Steve: (...) I assume that L3P reports the relevant lines, so it is trivial to remove one of the offending ones. (...) Right. Set a reasonably large threshold (0.1?) and reject based on it. Jacob (23 years ago, 18-Oct-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Parts Tracker - Using L3P-check to scan submitted files
|
|
(...) [snip areas of agreement] (...) Which is sloppy, but not a killer error. (...) I didn't list the non-coplanar message with the "reject" group is because the thresholds of coplanarity are variable, not fixed. So we need to agree on what level (...) (23 years ago, 18-Oct-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Parts Tracker - Using L3P-check to scan submitted files
|
|
Steve: (...) [...] Seems okay. (...) [...] Seems okay. (...) I would say yes. The last two definitely should, since they indicate unneeded resource use. The first one should really be split in to two triangles, if it really is intended to be (...) (23 years ago, 18-Oct-01, to lugnet.cad.dev.org.ldraw)
|
