 | | Re: DAT voting page up
|
|
jonathan wilson wrote in message ... (...) on (...) Some POV Ray libs can render the logo on the studs and round the edges of the bricks, but I usually render without these, mainly because my renderings will never likely be that close up, but also (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
Terry K wrote in message <36d4f44c.3127860@lu...et.com>... (...) about is (...) have (...) by (...) you (...) This is certainly true, but with some research dimensions can be determined by comparison with known parts via this very discussion and (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
(...) Hi x996 / x998 Do the 1 x 8 light bricks really look like this - what set are these from. On the Blacktron II Base the two 1 x 8 light bricks are identical with the lights midway between studs - and the studs have hollow tops. Chris Dee (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | RE: DAT voting page up
|
|
(...) Thank you for your effort Terry. Here are some comments from "l3p -check". /Lars WARNING "2552.DAT" Line 479: Identical vertices: 2 24 -150 0 10 -150 0 10 WARNING "2621.DAT" Line 204: Identical vertices: 4 16 36 8 -66 40 8 -63 36 8 -66 33.78 8 (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | RE: DAT voting page up
|
|
(...) 71427.dat Electric 9V Mini-Motor uses box3#8p.DAT (Note the p!) /Lars (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | RE: DAT voting page up
|
|
(...) Yes, there is a huge amount of studs hiding inside other bricks. Anybody got an intelligent algorithm? This would be applicable for LDLite too and save a lot of unnecessary rendering. However, watch out for transparent bricks... /Lars (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | RE: DAT voting page up
|
|
(...) POV-Ray certainly requires a LOT of memory when using the L3P -q3 option. Parsing time increases very much. However, the rendering time isn't that much longer as one could have feared. Probably because POV-Ray has some efficient internal (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | RE: DAT voting page up
|
|
(...) Yes, but from the LDraw triangles and quads alone it requires some heavy analysis to decide whether to add or subtract the small offset. I think we have some patterned inverted slopes... /Lars (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | RE: DAT voting page up
|
|
(...) No. I should have been more specific: If two surfaces coincide, the viewing ray will due to small numerical inaccuracies sometimes hit the one surface first and sometimes the other surface first. If the surfaces are colored differently (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: Java LDraw/LDLite
|
|
Todd Lehman wrote in message ... (...) Why thank you =) (...) Indeed - I've got a guitar tabulature editor written entirely in Java and it runs as happily on a Win32 box as my friend's Linux box and apparently another friend's Mac. Rumour has it (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
(...) I am not worried about part numbers on the parts. What I am concerned about is the overall accuracy of a part that is modelled from a picture. If you have followed l-cad for any time at all, you recall much discussion about part dimensions. (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
(...) Perhaps because it would be too small to resolve clearly when rendering - and would add greatly to rendering times. -- Terry K -- (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
(...) Well, "Pattern" just sort of became a standard way of identifying a patterned part. "Logo" I think should refer more to a specific type of pattern. Necessary? I don't know. But I seem to be blindly following the convention. (...) In a perfect (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | hose spreadsheet
|
|
what ever happended to the flexable hose generating spread-sheet? did it get finished? is it avaliable? where can i get a copy? (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | baseplate
|
|
does anyone have the baseplate 32 x 32 raised with ramp as a real bit of plastic? if so could they please tell me the arangement of studs in the "pit" in the middle so I can fix my part (when i fix this i will remove the needs work tag) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
(...) i had lego when i was young but i do not have any internions to buy lego any time soon because if i got back into it it would cost a fortune. also regarding the details noone has modeled the small imprinted lego logo on parts (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: MAX2DAT version 1.0 complete
|
|
onyx wrote in message ... (...) Well it sounds like a great addition to Ldraw utilities. Good work. Just wish I could use it myself. Roy (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
jonathan wilson wrote in message ... (...) battery (...) My thought on that would be yes if the part can be opened or exposed somehow in the model it is used in. I've actually been trying to come up with a program that with strip the unexposed or (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
Terry K wrote in message <36d4980d.635296@lugnet.com>... (...) don't (...) you (...) having (...) Geez, Terry, its all relative. I've yet to see anyone try to model the few imprinted part numbers there are. Besides, if we start getting too picky (...) (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
i deliberatly chose simple parts such as the magnifying glass and the crystal ball. also i will consider borrowing parts. (26 years ago, 25-Feb-99, to lugnet.cad.dev)
|
