 | | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4
|
|
(...) After looking a little closer at other parts (and some contact with Tore), I have become convinced that the interior details are probably more than we need to model anyway. The only important interior structures are: Center stud Side ribs (the (...) (24 years ago, 9-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4 [DAT]
|
|
(...) Often the number remains the same across relatively minor variations. Sometimes even across major variations. (...) Sort of, but there's another potential primitive lurking about, that is even more useful, to provide good modeling. This is a (...) (24 years ago, 8-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | x476.dat, "Bar 12L with Hollow Studs, Towball, and Slit (aka Sailboard Mast)" [DAT]
|
|
This piece is used for the Cutter in 6277, "Imperial Trading Post", as well as in other sets. This was the most accurate descriptive name I could think of. :-/ Please LMKWYT. Thanks, Franklin 0 Bar 12L with Hollow Studs, Towball, and Slit (aka (...) (24 years ago, 8-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Torus primitive discussion. was( Updated Primitive - 1-8t0102 1/8 torus)
|
|
(...) Because I was thinking that each section covered 90-degrees of the major circle. Otherwise, they'd be named 16t*0301.dat, since each is 1/16 of a complete torus. (I suppose they could be described as 1/8 of an inner (or outer) torus, but I (...) (24 years ago, 8-Jan-01, to lugnet.cad.dat.parts.primitives)
|
| |
| | Torus primitive discussion. was( Updated Primitive - 1-8t0102 1/8 torus)
|
|
(...) Hello, Torus comments are welcome from anyone who it may affect. I'm sure there are others out there that will use these when they become familiar with them. (...) Ok, give it a throw... :-) (...) Yes, I am afraid so. (...) I can agree to (...) (24 years ago, 8-Jan-01, to lugnet.cad.dat.parts.primitives)
|
| |
| | Part Correction: #3069p17; Tile 1 x 2 w/ Stingray Control Panel Pattern [DAT]
|
|
Okay, after some discussion as to the origin, This part is being renamed, and NOT renumbered. Old: Tile 1 x 2 w/ SW Control Panel Pattern New: Tile 1 x 2 w/ Stingray Control Panel Pattern 0 Tile 1 x 2 w/ StingRay Control Panel Pattern (Needs work) 0 (...) (24 years ago, 8-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3069p17; Tile 1 x 2 w/ SW Control Panel (Needs work)
|
|
(...) WOW! I had no idea this stuff was so, so... I dunno. Anyway, thank you for your guidance. Joe (24 years ago, 8-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3069p17; Tile 1 x 2 w/ SW Control Panel (Needs work)
|
|
OK, now that someone else has confirmed that this part was introduced with the Sting Rays ("(URL) of the Aquazone theme, I'd suggest that you rename the description as follows: "Tile 1 x 2 - StingRay Control Panel (needs work)" As far as the pattern (...) (24 years ago, 8-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3069p17; Tile 1 x 2 w/ SW Control Panel (Needs work)
|
|
(...) [shrug] I don't know, either. How about posting an enlarged image of this part to BrickShelf, and then posting a message to ".space" with the URL of this image, asking the space-guys for a positive identification? That's what I'd do. Franklin (24 years ago, 7-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3069p17; Tile 1 x 2 w/ SW Control Panel (Needs work)
|
|
(...) Franklin, Well, okay. Just goes to show how new I am. I didn't see it on the tracker or any part listings. How should it be labeled then? Joe (24 years ago, 7-Jan-01, to lugnet.cad.dat.parts)
|
