Subject:
|
Re: *** LDView Version 2.1 Released ***
|
Newsgroups:
|
lugnet.cad
|
Date:
|
Mon, 5 Jan 2004 23:28:19 GMT
|
Viewed:
|
683 times
|
| |
|
|
In lugnet.cad, Willy Tschager wrote:
> In lugnet.announce, Travis Cobbs wrote:
> [COPY'N'PASTE]
>
> > * Added ability to specify the camera's latitude and longitude on the
> > command line (similar to L3P's -cg command line option).
> > * Added support for custom colors inside model files (as well as inside
> > ldconfig.ldr) using the 0 COLOR meta-command.
> > * Added ability to specify extra part/sub-model search directories.
>
> :-))))))))))))))))))))))))))))))))
>
> many, many THX for adding those!!!
You're welcome. As an aside to other users that have feature ideas, I believe
that Willy suggested/requested all of the above. I tend to be fairly arbitrary
about which feature requests get implemented and which ones don't (I'm more
likely to work on those that strike my fancy), but I do make an effort to pay
attention to requests.
> > * Fixed SaveSnapshot so that it now only loads the model once; previously it
> > would load it and then immediately reload it, doubling the load time.
>
> this seams not being true for the command line. actually now it loads the model
> twice, taking twice as much time ;-)
Hmm, I'll have to look into that. I thought I had it fixed. The SaveSnapshot
functionality behaves very differently on newer video cards with good OpenGL
support than on older ones with less good support. I'll have to determine if
both code paths are broken or just one of them.
> > * Fixed command line parsing to properly handle quotes around a filename
> > specified as part of an option.
>
> superhint for all the absolute command line beginners out there (from an
> absolute beginner). the syntax for the -SaveSnapshot command is:
>
> -"SaveSnapshot=c:\...blanks...\xxxx.bmp(png)"
I'm pretty sure the above won't work. The point listed was put in the change
history because I fixed it such that is should now accept either of the
following:
-SaveSnapshot="C:\...blanks...\xxx.bmp(png)"
"-SaveSnapshot=C:\...blanks...\xxx.bmp(png)"
As you (Willy) noticed, the first form didn't work before. However while I
won't rule it out entirely, I will be surprised if the quotes after the dash
work. What I can say is that the only spaces allowed in the option are the ones
in the filename itself, and if they exist, they require the quotes to be
present.
--Travis Cobbs
|
|
Message has 1 Reply:
 | | Re: *** LDView Version 2.1 Released ***
|
| (...) UUUUUPS!!! big, huge, enormous, gigantic typo! what I tried to say was "-SaveSnapshot=C:\......bmp(png)" BTW setting the quotes blanks work also fine in the path name. there are no problems with a command like this: "-SaveSnapshot=C:\My (...) (21 years ago, 7-Jan-04, to lugnet.cad)
|
Message is in Reply To:
| | Re: *** LDView Version 2.1 Released ***
|
| (...) [SNIP] (...) [COPY'N'PASTE] (...) :-)))...))) many, many THX for adding those!!! (...) this seams not being true for the command line. actually now it loads the model twice, taking twice as much time ;-) (...) superhint for all the absolute (...) (21 years ago, 5-Jan-04, to lugnet.cad)
|
12 Messages in This Thread:
  
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
