Subject:
|
Re: door 1 x 3 x 1 new patterns and errors in parts on PT
|
Newsgroups:
|
lugnet.cad
|
Date:
|
Wed, 14 May 2003 13:31:59 GMT
|
Viewed:
|
1412 times
|
| |
|
|
Steve,
I sent you an email regarding my inability to access the PT (either my
password has been reset or my authoring privleges have been reset). I can't
make any corrections to my parts until then.
But the files are ready to submit. I corrected
3822p09 (quick)
3004p18 (corrected subpart line, separated pattern out)
3069bp18 (separated pattern out)
3004s01 (noticed that the inner box needed a BFC INVERTNEXT)
and the new subpart for the POLICE pattern is 3069bs18. Which looks to need
a few edits first (see other branch of thread).
I think Thomas Burger is the author of 3822p03, so hopefully he's been
reading this thread and will make the quick correction on the door.
John
In lugnet.cad, Steve Bliss writes:
> In lugnet.cad, Niels Karsdorp wrote:
>
> > Browsing the PT for the new subpart for the door 1 x 3 x 1 without
> > stud I also took a look at the complete door parts on the PT and
> > noticed the following errors in two parts:
> >
> > 3822p03 Door 1 x 3 x 1 Left with Yellow / Red Stripe Pattern
> > Misspelled reference to 'sstud.dat', should be 'stud.dat' I assume
> >
> > 3822p09 Door 1 x 3 x 1 Right with Fire Logo Pattern
> > Should be 'Left' instead of 'Right'.
>
> Do you mind fixing these and resubmitting them?
>
> > Two more patterns (need pattern numbers):
> > * Shell Logo Pattern
> > * POLICE Pattern
> > (I assume p18 for the police patterns matching
> > other parts with the same pattern. The shell logo
> > is also used in 3004p60, but p60 doesn't match the
> > town-category)
>
> I think the SHELL logo is used on some other parts (goes off searching).
> Yep! See
> http://www.ldraw.org/cgi-bin/ptscan.cgi?q=shell
> you can use pt1 or pt2.
>
> I think p18 is OK for for the POLICE.
>
> > Since the POLICE Pattern is already created by
> > John Riley in 3069bp18 and 3004p18 and the doors
> > have the same pattern (I have all 3069b, 3004
> > 3821 and 3822 with the POLICE pattern in real)
> > I think it is useful to put the POLICE pattern
> > into a subfile and reference to that subfile
> > in all of these parts.
>
> nod, ok, that sounds good. You want to do this?
>
> > (part 3004p18 references to 3004s01.DAT instead
> > of s/3004s01.dat)
>
> Oops. Can you fix this as well?
>
> Steve
|
|
Message is in Reply To:
 | | Re: door 1 x 3 x 1 new patterns and errors in parts on PT
|
| (...) Do you mind fixing these and resubmitting them? (...) I think the SHELL logo is used on some other parts (goes off searching). Yep! See (URL) can use pt1 or pt2. I think p18 is OK for for the POLICE. (...) nod, ok, that sounds good. You want (...) (23 years ago, 14-May-03, to lugnet.cad)
|
12 Messages in This Thread:
 
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
