Subject:
|
Re: door 1 x 3 x 1 new patterns and errors in parts on PT
|
Newsgroups:
|
lugnet.cad.dat.parts
|
Date:
|
Mon, 12 May 2003 15:55:42 GMT
|
Viewed:
|
1730 times
|
| |
|
|
In lugnet.cad, Niels Karsdorp writes:
> 3822p09 Door 1 x 3 x 1 Right with Fire Logo Pattern
> Should be 'Left' instead of 'Right'.
As soon as I get my PT access restored, I'll make this correction. Thanks
for picking up on this.
> (I assume p18 for the police patterns matching
> other parts with the same pattern. The shell logo
> is also used in 3004p60, but p60 doesn't match the
> town-category)
I picked p18 for police because it was unused across a large variety of
parts. There's a variation on the POLICE pattern for the 1 x 4 x 3 panels
(4215ap18) which is a slightly different font. I imagine that the new World
City police line also uses a somewhat different font (we'll see in a few
months). I'm not sure, but I'd stick with p60 for the Shell logo now that
it's been used. Need to hear from Steve or Chris to be sure.
>
> Since the POLICE Pattern is already created by
> John Riley in 3069bp18 and 3004p18 and the doors
> have the same pattern (I have all 3069b, 3004
> 3821 and 3822 with the POLICE pattern in real)
> I think it is useful to put the POLICE pattern
> into a subfile and reference to that subfile
> in all of these parts.
> (part 3004p18 references to 3004s01.DAT instead
> of s/3004s01.dat)
>
> Niels
I can go ahead and separate the pattern into a subfile and upload it when
access is restored. I'll post the subfile to cad.dat.parts as well in the
meantime so you (and anybody else) can try it out. And thanks for catching
my subfile mistake.
It seems that you and I have done a lot of similar patterns. I'd like to
avoid duplicating efforts if possible. Are you working on any new patterns?
The parts I currently am working on are:
3005p?? Brick 1 x 1 with Bold White Number 2 (ready for submission)
3068bp?? Tile 2 x 2 with Bold White Number 2 (needs work)
30528 Arch 1 x 8 x 6 (ready for submission)
30535 Propeller Housing 2 x 4 x 4 (ready to submit)
30603 Slope Brick 2 x 2 x 1 with Pistons (needs work)
43719 Wedge 4 x 4 Plate (finished this yesterday, ready to submit)
x??? Plate 1 x 1 Round with Tabs (peeron x249, needs a x###)
4864p?? Panel 1 x 2 x 2 with Motorcycle pattern (from 6699, needs work)
4864p?? Panel 1 x 2 x 2 with Bicycle pattern (from 6699, needs work)
Thanks for your help.
John Riley
|
|
Message has 1 Reply:
Message is in Reply To:
 | | door 1 x 3 x 1 new patterns and errors in parts on PT
|
| Browsing the PT for the new subpart for the door 1 x 3 x 1 without stud I also took a look at the complete door parts on the PT and noticed the following errors in two parts: 3822p03 Door 1 x 3 x 1 Left with Yellow / Red Stripe Pattern Misspelled (...) (22 years ago, 12-May-03, to lugnet.cad)
|
12 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
