 | | Re: I want to become a reviewer
|
|
(...) So I understand that studlogos may face any direction as long as they are not mirrored? How about a mix of rotated studlogos on one single part instead of all studslogos facing the same direction? E.g. some studlogos readable when the part is (...) (20 years ago, 4-Nov-04, to lugnet.cad, FTX)
|
| |
| | Re: cylinders missing conditional lines?
|
|
(...) I checked a few official parts that use the 2-4cyli primitive. And all the parts I have checked so far are missing the conditional line at one end of the cylinder. So I suspect that part authors expect that all partial cylinder primitives have (...) (20 years ago, 4-Nov-04, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: I want to become a reviewer
|
|
(...) Yes - these kind of errors are not a cause for a hold. I'm with Orion on stud rotation, but I'd prefer not to have parts/subparts designed in a way that causes mirrored studs. We have set a precedent with car doors, by moving the stud from the (...) (20 years ago, 4-Nov-04, to lugnet.cad, FTX)
|
| |
| | Re: half size 3004
|
|
(...) Ok, Thank you :) I'd be happy to beta test 3.0 when you make it available. Thanks again. (20 years ago, 4-Nov-04, to lugnet.cad)
|
| |
| | Re: cylinders missing conditional lines?
|
|
(...) This thread pops up from time to time and never seems to get resolved. (URL) think the problem is this: If you fix the all the primitives, then you really must check all the parts that use them. So we end up ignoring it and moving on. If (...) (20 years ago, 4-Nov-04, to lugnet.cad.dat.parts.primitives)
|
| |
| | cylinders missing conditional lines?
|
|
When using the 2-4cyli primitive I noticed one conditional line missing, so I compared all different cyli primitives. Some have conditional lines at both ends, some have not. 1-4cyli: conditional lines at both ends 1-8cyli: conditional line at one (...) (20 years ago, 4-Nov-04, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: half size 3004
|
|
(...) Thanks. It's definitely a problem in LDView. It's caused by a known bug in LDView's handling of the Seam Width option. (It was brought to my attention maybe a month or so ago by another post.) There's nothing wrong with the part files. If you (...) (20 years ago, 4-Nov-04, to lugnet.cad)
|
| |
| | Re: half size 3004 [DAT]
|
|
(...) Ok, after some investigation, I have created this: 0 ROTATION CENTER 0 0 0 1 "Custom" 0 ROTATION CONFIG 0 0 1 0 0 -16 -20 1 0 0 0 1 0 0 0 1 2458.DAT 1 0 0 -16 0 1 0 0 0 1 0 0 0 1 3004.DAT 1 0 0 -16 20 1 0 0 0 1 0 0 0 1 3004.DAT 1 0 0 -16 40 1 (...) (20 years ago, 4-Nov-04, to lugnet.cad)
|
| |
| | Re: I want to become a reviewer
|
|
(...) Since stud logos are not part of the DAT format, the fact that they are rotated or mirrored is not a problem with a part. That said, since most users like to use the stud logo option for some renders, if problems with the stud logos are (...) (20 years ago, 4-Nov-04, to lugnet.cad, FTX)
|
| |
| | Re: I want to become a reviewer
|
|
(...) How imported is the orrientation of the studlogos? Should these face exactly the same direction as the real part? Or do they just have to be readable (thus not mirrored) and all studlogos on one part face the same direction (unless the real (...) (20 years ago, 3-Nov-04, to lugnet.cad, FTX)
|
