 | | Re: Howto on : BFC "Hold" on 47457.dat
|
|
(...) It's a bug in L3Lab - it assumes the top-level file is BFC by default. Since most model files will naturally be BFC-compliant, this works great for viewing models. But it doesn't work correctly for viewing part files directly. Steve (20 years ago, 1-Nov-04, to lugnet.cad)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) Thanks for the direction. I really though I had done something wrong with setting up my parts lib. I'll give Peeron a try in the future as well. (20 years ago, 1-Nov-04, to lugnet.cad, FTX)
|
| |
| | Re: Howto on : BFC "Hold" on 47457.dat
|
|
(...) Hummm... aside from the apparent L3Lab bug, how DO I make 47457.dat BFC compliant? I'm sure the process is more than just flipping the image around to see if any red shows up. (20 years ago, 1-Nov-04, to lugnet.cad)
|
| |
| | Re: LDGlite and LPub
|
|
In lugnet.cad.dev, Don Heyse wrote: <snip> (...) Thanks Don, I got it working for both assembly images and part images. Kevin (20 years ago, 1-Nov-04, to lugnet.cad.dev)
|
| |
| | Re: Problem to synthesize Rubber Tread
|
|
(...) Gustavo, Try rotating the left constraint 90 degrees about the axle and resynthesize until it is fixed. Then do the same with the right constraint. Kevin (20 years ago, 1-Nov-04, to lugnet.cad)
|
| |
| | Re: Howto on : BFC "Hold" on 47457.dat
|
|
Given that the part isn't BFC-certified (no BFC comments in the file at all), it by definition cannot contain any BFC errors. For reasons I don't understand, L3Lab is displaying it as if it were BFC-certified. I would suggest pointing out to Steffan (...) (20 years ago, 1-Nov-04, to lugnet.cad)
|
| |
| | Howto on : BFC "Hold" on 47457.dat
|
|
I got an e-mail notice that a review of 47457.dat revealed BFC errors. I really don't know how to check for BFC compliance. All I did was to turn the part around to see if any of it was red. I know there's a caveat that some lines bleed red. I (...) (20 years ago, 1-Nov-04, to lugnet.cad)
|
| |
| | Problem to synthesize Rubber Tread
|
|
Hi, I have problem to draw a Rubber Tread with MLCad and LSynth, when the process finishes it shows an intermitent Rubber Tread. Please any help will be apreciated (URL) moderation) Gustavo Brinck Lugnet Member 566 Santiago Chile (20 years ago, 1-Nov-04, to lugnet.cad)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) Please understand that I wasn't harping on it to you guys. I had my bit of that, then Steve explained the situation to me (that it's a known problem, that it's being discussed, and that all Wedge Plates will probably end up as Wings), and now (...) (20 years ago, 31-Oct-04, to lugnet.cad)
|
| |
| | Re: 3 x 2 Wedge Plates
|
|
(...) Gah! Um, they have been made for LDraw, but those parts have not yet been approved. You can download the requisite files from here: (URL) Right> (URL) Left> Make sure you grab the subfiles and put them all in the right directories or the parts (...) (20 years ago, 31-Oct-04, to lugnet.cad, FTX)
|
