 | | Re: Strange part/file conversion problem
|
|
"Allan Bedford" <ExpertBuilder-DELET...otome.com> skrev i meddelandet news:HHMnt3.1ps6@lugnet.com... (...) through (...) assembly (...) Are you using LGEO parts? There are some parts with the wrong number there, so that could explain it. (20 years ago, 6-Oct-04, to lugnet.cad)
|
| |
| | Re: Strange part/file conversion problem
|
|
I've seen this problem a few times myself. I've found there are more parts that have this problem. Up till now I've found at least three parts. 1) the bottom end of the hinge as mentioned below (hinge plate 2x5 base, 3149.dat, converts to tipper (...) (20 years ago, 5-Oct-04, to lugnet.cad)
|
| |
| | Re: I want to become a reviewer
|
|
(...) "cut" or "remove"... as in removing many words that you choose not to quote. Some say the word is onomapoetic, in that some think it sounds like the sound scissor blades make as they cut things. (20 years ago, 6-Oct-04, to lugnet.cad, FTX)
|
| |
| | Re: I want to become a reviewer
|
|
Thanks, I couldn’t fall to sleep last night (late computer work and sorting all my building instruction into pockets and binders) so I wrote a few things down… I wouldn’t mind if it was made into a tutorial if I had the chance of checking the (...) (20 years ago, 6-Oct-04, to lugnet.cad, FTX)
|
| |
| | Re: I want to become a reviewer
|
|
Well, running a bit back and forth in the file will give you a sense of the part just as well, and the you avoid starting out with a maze of lines: The biggest problem is that without the framing lines, the polygons is extremely difficult to figure (...) (20 years ago, 6-Oct-04, to lugnet.cad, FTX)
|
| |
| | Re: Working on 6032.dat Brick 2 x 3 x 1 & 2/3 Octagonal offset
|
|
I wasn't only talking about abandoned parts, but all the ones people are working on that'll take a long time to finish. (since the other ones probably gets finished before somebody else starts on them). But now you're forgiven (for the sins you’ve (...) (20 years ago, 6-Oct-04, to lugnet.cad.dat.parts, FTX)
|
| |
| | Layout: Do you use it?
|
|
Hi, How many of you have used the layout/callout generation facility in LPub? There are things I want to change, and I want to know if backward compatibility is an issue. Kevin (20 years ago, 6-Oct-04, to lugnet.cad)
|
| |
| | Re: Strange part/file conversion problem
|
|
In lugnet.cad, Allan Bedford wrote: [snip] (...) If you try this again today do you still run into the same error? If so, send me files and I'll try to recreate it on my machine. (...) Kevin (20 years ago, 6-Oct-04, to lugnet.cad)
|
| |
| | Re: BFC inversion...
|
|
(...) It may be required by the part tracker, but it isn't required by the BFC spec. The spec specifically says that the first instance of any BFC command in a file implicitly turns on BFC certification in the file (unless of course it's a 0 BFC (...) (20 years ago, 6-Oct-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Strange part/file conversion problem
|
|
(...) I was able to resolve it by manually editing the .pov file once it was created. POVRay would reject the initial file, then I went in and edited out references to the wrong part, replacing them with references to the correct part. Then I simply (...) (20 years ago, 6-Oct-04, to lugnet.cad)
|
