 | | Re: Ldraw/MLCAD question
|
|
This discussion about raised a suggestion for a nice feature for MLCad (and perhaps also for other LDraw building software): A possibility to filter all patterned bricks. And have this filter be enabled and disabled with a press of a button. (The (...) (21 years ago, 14-May-03, to lugnet.cad)
|
| |
| | Re: Ldraw/MLCAD question
|
|
(...) I *believe* it compiles the list based on what's in C:\LDraw\PARTS\, so if you add parts to this directory, yes. He'd have to cut out the undesireables each time because of this fact. If you put unofficial parts in there (or in my case, I put (...) (21 years ago, 14-May-03, to lugnet.cad)
|
| |
| | Re: Ldraw/MLCAD question
|
|
(...) I've added parts to PARTS.LST, and I've placed the DAT files for the new parts with the standard parts. Will my new parts still be in PARTS.LST if I download a parts update and re-compile PARTS.LST? Is the list generated from the parts on-hand (...) (21 years ago, 14-May-03, to lugnet.cad)
|
| |
| | Re: Ldraw/MLCAD question
|
|
(...) The hard way: Open the file C:\LDraw\PARTS.LST. Find the entries you don't want, and manually remove them. You won't see them on the parts list in any LDraw-based program you use, but if you're never going to use them...it'll work. (note, each (...) (21 years ago, 14-May-03, to lugnet.cad)
|
| |
| | Re: Ldraw/MLCAD question
|
|
<snip> (...) Umm.. nevermind on this first question. It seems I didn't properly install complete.exe (...) (21 years ago, 14-May-03, to lugnet.cad)
|
| |
| | Ldraw/MLCAD question
|
|
I've got a MLCAD/LDraw question. Ive just loaded it onto my computer, although I'm not sure I downloaded/expanded every component to just where it should be (like in the same folder, etc), although i've tried to move everything back now. When I open (...) (21 years ago, 14-May-03, to lugnet.cad)
|
| |
| | Re: POLICE Pattern (was Re: door 1 x 3 x 1 new patterns and errors in parts on PT)
|
|
(...) I think the O could be done with overlapping rings (and roughly 3/4 of the C), now that I think about it (I may try it before converting everything over to quads). But considering the C cannot be done without using quads, it may look odd that (...) (21 years ago, 14-May-03, to lugnet.cad.dat.parts)
|
| |
| | Re: door 1 x 3 x 1 new patterns and errors in parts on PT
|
|
Steve, I sent you an email regarding my inability to access the PT (either my password has been reset or my authoring privleges have been reset). I can't make any corrections to my parts until then. But the files are ready to submit. I corrected (...) (21 years ago, 14-May-03, to lugnet.cad)
|
| |
| | Re: Ver 0.73.1 & Minifig Wizard
|
|
Hello there, I have exactly the same problem: since the installation of the new version the minifig wizard gives an 'this program has performed an illegal operation' error (21 years ago, 12-May-03, to lugnet.cad.leocad)
|
| |
| | Re: POLICE Pattern (was Re: door 1 x 3 x 1 new patterns and errors in parts on PT)
|
|
(...) Me, too. But there aint no rings with a x-radius-difference of 1 and z-radius-difference of 1.125. Or you need to have overlapping rings. Even using ndis, segm (chord) primitives and triangles filling up is not possible, because the outer (...) (21 years ago, 14-May-03, to lugnet.cad.dat.parts)
|
