 | | Re: Brickbay Temp URL Available
|
|
You just start LDLite from a command prompt, with a -MS option. MS is for "Mode Save". Something like: c:\ldraw\ldlite\ldlite 3001.dat -MS (assuming LDLite is installed in c:\ldraw\ldlite\) Steve (...) (24 years ago, 30-May-00, to lugnet.market.shopping, lugnet.cad)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) typo typo... yes, I meant to say I can't be on the committee. I guess if I were committed, I'd have lots of time... if I could only convince my therapist to allow LEGO as therapy. (...) take that to off-topic.debate, it's debatable. (...) (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) Put me down for a minumum of 100 USD (and like Larry, I'm good for more if it is necessary to get the project off the ground). (...) I know some people say you should be committed Larry, but that's not what we're talking about... Tim just (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) be (...) at. I (...) Ya, right after I pressed fire I realised it was a bit cryptic. Lets try again. What is "at cost"? (we all agree that it makes sense to press 1000 of them because that's where the cost per starts to get cheap) One *could* (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) Thanks! (...) I'm not completely undersrtanding... I know that 50 at cost is what they asked me for in an email - could you clarify 1000/1050? I *think* I understand what you're getting to but I'm not 100% sure. Its 5am. -Tim (URL) timcourtne (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw to display at Legoland California for Kidvention
|
|
(...) :( You're going to miss some serious festing....hope you can make it . (...) Sure there is. To lighten my load travelling, either you could send them with John Neal, or ship them to Terry K or Mike P. When you get ready to loan them out we can (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw, lugnet.legoland.california)
|
| |
| | Re: [Part] 4515p03.dat - Slope Brick 10 6 x 8 with Slate Roof Patt ern
|
|
(...) Can someone else try looking at both the first and second versions of hte part and see if they see bleedthrough? It might have been me. I was viewing it with MLCad 1.7 ++Lar (24 years ago, 29-May-00, to lugnet.cad.dat.parts)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) Put me down for a minimum of 200 USD in funding for this. If we come up short, I'm in for up to 500. I would prefer that others cover it though if at all possible. I don't have time to be on the committed, though. The reimbursement procedure (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw to display at Legoland California for Kidvention
|
|
(...) most (...) such (...) imagination. (...) don't (...) Thanks for the clarification! I think you're spot on. (...) That sounds pretty swell. (...) generated (...) I do have physical models for all of that except the blue version of the hopper. (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw, lugnet.legoland.california)
|
| |
| | Re: 32198 Technic Gear 20 Tooth Bevel
|
|
Good part! However, to match the orientation of the previous bevel gear, it should be rotated 180 deg around the Y axis. I would also prefer that it was centered in the origin. Right now it is centered in Z=5. Fredrik (24 years ago, 29-May-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Obscure ldraw descriptions
|
|
(...) The point of having the name "Technic Pin with Friction" (not "technic pin with friction" as you refered to) is to make sure that the part falls in the same category as the part "Technic Pin". This is also why the names of the Technic chain (...) (24 years ago, 29-May-00, to lugnet.cad.dev)
|
| |
| | Re: Looking for parts
|
|
I did not make either of the parts you refered to, I only posted them because somone asked for them. And anyway somone is working on the helicopter skids. (24 years ago, 29-May-00, to lugnet.cad)
|
| |
| | Re: Looking for parts
|
|
(...) At (URL) you can see Jonathan Wilson's mockup. (...) Jonathan Wilson did that, too, but I can't find it. (...) (24 years ago, 29-May-00, to lugnet.cad)
|
| |
| | Re: LDraw to display at Legoland California for Kidvention
|
|
(...) Mee too....well in February. :) (...) Ok, email me closer to the date when your plans are more set, and I'll see if we still need some. You're definitely welcome to chill with us at the booth! :) (...) Great job! But thats a *really* hard job (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw, lugnet.legoland.california)
|
| |
| | LDraw CD-ROM Update/Funding and dealing with group funds
|
|
Greetings Just to update everyone on the CD project: Currently I have to do some work with the HTML guide, and pass off some work for HTML reformatting of a couple resources to others while I'm away for a few days. A few programs need to be (...) (24 years ago, 29-May-00, to lugnet.cad, lugnet.cad.dev, lugnet.cad.dev.org.ldraw, lugnet.org) !
|
| |
| | Obscure ldraw descriptions
|
|
i've noticed that a few ldraw pieces have extremely drawn-out descriptions. for instance: we have the "technic pin with friction", 4459.dat 'with friction'? it should be called a "technic friction peg", or "technic friction pin" 50.dat has a good (...) (24 years ago, 28-May-00, to lugnet.cad.dev)
|
| |
| | Re: Looking for parts
|
|
(...) <snipped one piece> (...) Hi Jim, Looks like I have some free time this weekend; I'll give the skids a shot. If my eyes haven't failed me, it looks like part #30248. -Chris (24 years ago, 28-May-00, to lugnet.cad)
|
| |
| | Re: LDraw to display at Legoland California for Kidvention
|
|
(...) I agree as well. Again, this is the problem you get when a couple spaceheads run a display ;) It'd be nice to have some train models, because the train layout is going to be right across the tent from us. (...) 99% of the time. We're going to (...) (24 years ago, 28-May-00, to lugnet.cad.dev.org.ldraw, lugnet.legoland.california)
|
| |
| | 32198 Technic Gear 20 Tooth Bevel [DAT]
|
|
0 Technic Gear 20 Tooth Bevel 0 Name: 32198.dat 0 Author: Marc Klein 0 Created with stl2dat conversion tool 0 Un-Official LCad part 1 16 -12 0 0 0 0 -1 -1 0 0 0 10 0 2-4cyli.dat 1 16 -12 0 0 0 0 -1 -1 0 0 0 1 0 2-4edge.dat 1 16 -12 0 10 0 0 -1 -1 0 (...) (24 years ago, 28-May-00, to lugnet.cad.dat.parts)
|
| |
| | Technic Gear 20 Tooth Double Bevel [DAT]
|
|
0 Technic Gear 20 Tooth Double Bevel 0 Name: g20d.dat 0 Author: Marc Klein 0 Created with stl2dat conversion tool 0 Un-Official LCad part 1 16 -10 0 10 0 0 -1 1 0 0 0 -20 0 2-4cyli.dat 1 16 -10 0 10 0 0 -1 1 0 0 0 -1 0 2-4edge.dat 1 16 -10 0 -10 0 0 (...) (24 years ago, 28-May-00, to lugnet.cad.dat.parts)
|
