| | Handyboard construction problems
|
|
I am in the process of assembling a Handyboard. All had gone well until I got to the stage where you download the code to the HB for the first time. This is before the memory is installed. I used HBDL to download with the register set to 0x0c. I got (...) (27 years ago, 23-Oct-97, to lugnet.robotics.handyboard)
|
|
| | RC motor connection
|
|
Hi, Did anyone know how to connect commercial electronic speed controllers to HB for powering high-current RC (20A to 100A) motors? Billy Kwong (27 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
|
|
| | Re: Rob Gaunts Last Message
|
|
Whoa, i just realized that the instructions *are* correct. Here's why. For this voltage test, the instructions assume you are powering your board from the DC adapter. This should give the 15 volts mentioned, unless: * you hooked up the battery pack (...) (27 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
|
|
| | Re: Rob Gaunts Last Message
|
|
(...) the instructions are wrong -- you should be seeing about 9v, which is the voltage on the nicad pack. i will revise the instructions. thanks for pointing out the problem. fred (27 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
|
|
| | Rob Gaunts Last Message
|
|
I sent out a message few minutes ago listing all sorts of problems I was having. Don't worry about it. I just figured it all out. I was using lib_r22.lis instead of lib_hb.lis in IC. Now things are working fine except that the voltage at pin 8 of (...) (27 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
|
|
| | Digital Ins and Motor Outs
|
|
I have succesfully loaded pcode_hb.s19 and run IC with my Handyboard (finally). However, I am having a few problems with the digital inputs and the motor outputs. The Start and Stop buttons work fine when testing the digital inputs using the (...) (27 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
|
|
| | AD: Wirz Electronics
|
|
Hello Everyone, We have a number of new Microcontroller products that we think you may be interested in: ---...--- Microchip PIC Products: "Programming and Customizing the PIC Microcontroller" book by Myke Predko (URL) Up The Pace" book by David (...) (27 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
|
|
| | Robot
|
|
Greetings, Just an FYI for everyone, I noticed a promo on the Discovery Channel that will feature a small robot. Strangely, the segment is to feature deformed frogs also. Not quite sure what the connection is , but....It was advertised to air (...) (27 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
|
|
| | Re: Board synch problem
|
|
Fred et.al.: Success! DLM, DL, and the others just wouldn't work for any of my hardware, but a colleague wrote a shareware application ( LOADHC11.EXE ) expressly to load bootstrap 256 byte loader program into page zero of internal RAM , including (...) (27 years ago, 20-Oct-97, to lugnet.robotics.handyboard)
|
|
| | Re: Board synch problem
|
|
two things you can try: 1. use DLM to download the CONFIG0C.S19 file. Make sure to use the -eeprom flag. This will cause it to burn the config register to the proper value. 2. Have you tried Randy Sargent's DL.EXE for DOS / Win 3.1 full screen DOS (...) (27 years ago, 20-Oct-97, to lugnet.robotics.handyboard)
|