Subject:
|
Re: Board synch problem
|
Newsgroups:
|
lugnet.robotics.handyboard
|
Date:
|
Mon, 20 Oct 1997 20:55:07 GMT
|
Original-From:
|
Craig Maynard (EE) <craig.maynard@saitSTOPSPAMMERS.ab.ca>
|
Viewed:
|
3670 times
|
| |
|
|
Fred et.al.:
Success! DLM, DL, and the others just wouldn't work for any of my
hardware, but a colleague wrote a shareware application ( LOADHC11.EXE )
expressly to load bootstrap 256 byte loader program into page zero of
internal RAM , including the CONFIG reg. I used it to set CONFIG to
0c, and then used hbdl to download pcode : No problems!
I don't know why your tried and true stuff wouldn't work for me, but at
least I found a solution. May I mail this ZIP file up to you?
Now... on to IC!
Craig
www.nucleus.com/~cybug
www.starcard.com/wcrg
On Mon, 20 Oct 1997, Fred G. Martin wrote:
> two things you can try:
>
> 1. use DLM to download the CONFIG0C.S19 file. Make sure to use the
> -eeprom flag. This will cause it to burn the config register to the
> proper value.
>
> 2. Have you tried Randy Sargent's DL.EXE for DOS / Win 3.1 full
> screen DOS mode. This is part of the freeware interactive C zip
> archive.
>
> let us know,
> fred
>
>
> In your message you said:
> >
> > I've noticed the only limited success I've had downloading pcode_hb.s19 is
> >
> > - with older slower systems that have _no_ modem cards installed using dlm
> > - with win95 or win311 systems using hbdl with no modem cards as well.
> >
> > The hbdl downloads them monitor, then the actual code, but complains that
> > config=0F every time (and fails)..
> >
> > If I set the config register in hbdl's dialog box to 0F, then it succeeds
> > in downloading without complaint, but ( of course ) won't run.
> >
> > I am anxious to impliment these wonderful boards in a course I am
> > developing for January, but am "thwarted". Can someone perform a
> > "thwart-removal"?
> >
> > Craig
> > www.starcard.com/~cybug
> > www.nucleus.com/wcrg
> >
> >
> >
> >
> > On Mon, 20 Oct 1997, John Duff wrote:
> >
> > > I'm not sure if my follow up message made it, appears to have bounced. Just • in
> > > case, the problem resolved when I took out the modem and network cards.
> > > Interestinly, the handyboard battery was nearly discharged when the problem
> > > surface. The cards had been present from the beginning, and the config had • not
> > > been changed. Thanks
> > >
> > > Fred G. Martin wrote:
> > >
> > > > last week someone reported solving this by letting the battery charge.
> > > > let us know if that works.
> > > >
> > > > am assuming that nothing changed in your config (cpu, cables, etc).
> > > >
> > > > fred
> > > >
> > > > In your message you said:
> > > > > My board has been running well for a few months. Last week it would not
> > > > > sychronize with IC 3.1. Also, no initial LCD display and heartbeat.
> > > > > After several attempts I was able to download pcode, but received a
> > > > > message suggesting the config register needed to be reinitialized. Sinc • e
> > > > > then, the initial LCD display is normal, with a heartbeat, but I can't
> > > > > sync with the board. Repeated attempts to download p-code and initializ • e
> > > > > the config register have failed using IC 3.1, hbdl and dl.
> > > > > Any thoughts? Thank you.
> > > > >
> > > > >
> > >
> > >
> > >
> > >
> >
>
|
|
Message is in Reply To:
 | | Re: Board synch problem
|
| two things you can try: 1. use DLM to download the CONFIG0C.S19 file. Make sure to use the -eeprom flag. This will cause it to burn the config register to the proper value. 2. Have you tried Randy Sargent's DL.EXE for DOS / Win 3.1 full screen DOS (...) (29 years ago, 20-Oct-97, to lugnet.robotics.handyboard)
|
6 Messages in This Thread:
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
