 | | Re: LDCC and Boosters
|
|
(...) It was (...) are to (...) for (...) instruction (...) surges (...) The CPU instructions can be anywhere from 1/8 to 1 microsecond (or longer) in duration. Assuming you could sync up to within 1us, you'd still be off by ~2% since the pulse (...) (21 years ago, 24-Jun-03, to lugnet.trains)
|
| |
| | Re: LDCC Resources?
|
|
(...) I have tried hard to make a bogie pickup with out success, mainly due to the difficulty fashioning a metalic pickup that is reliable. There is a disadvantage in powering the lights direct from the track (which of course is possible) and that (...) (21 years ago, 24-Jun-03, to lugnet.trains)
|
| |
| | Re: LDCC and Boosters
|
|
(...) I don't think you can, because there would be no sinc between the boosters. :( (...) I'd like to see this written into the code. It seems to be the only way that it would be possible to do it. (use one RCX as master and multi as slaves, all (...) (21 years ago, 24-Jun-03, to lugnet.trains)
|
| |
| | Re: LDCC and Boosters
|
|
(...) I'm wondering how you could possibly get the signals synced closely enough for this to work without a physical cable connecting the two RCX internals (clocks??? I dunno). What is the cycle timing on these compared to instruction clock rate? (...) (21 years ago, 24-Jun-03, to lugnet.trains)
|
| |
| | Re: LDCC and Boosters
|
|
(...) So, they're 10K, not 1K as they appear. Anyways, I'll be doing a write up of this sensor and the slave code soon. Mark (21 years ago, 24-Jun-03, to lugnet.trains)
|
| |
| | Re: LDCC and Boosters
|
|
(...) to (...) use a (...) you (...) connecting (...) I haven't really looked at commercial DCC boosters, but I have been looking at the various homebrew designs on the net. Haven't gotten past the "contemplation" phase, though. :-) (...) was (...) (...) (21 years ago, 24-Jun-03, to lugnet.trains)
|
| |
| | LDCC and Boosters
|
|
Has anyone had any success using DCC Boosters with LDCC? There are ways to connect Boosters of different brands to command stations (e.g., you can use a Digitrax Booster with an EasyDCC command station). Although to do this, you need to know which (...) (21 years ago, 24-Jun-03, to lugnet.trains)
|
| |
| | Re: LDCC Resources?
|
|
(...) I have installed several Digitrax DN142's. I really like the "Back EMF" load compensation function. It helps with voltage droop on curves and hills. Also, shortly I will be getting a couple TCS M1's. These are cheaper than the DN142's and have (...) (21 years ago, 24-Jun-03, to lugnet.trains)
|
| |
| | Re: LDCC Resources?
|
|
(...) Good question, here's a list of decoders I've heard of being installed inside a train motor (any others, anyone?): Digitrax DN121 Digitrax DZ143 Digitrax DN140 (discontinued product) Lenz LE0511W MRC AD330 Also, these decoders seem likely (...) (21 years ago, 24-Jun-03, to lugnet.trains)
|
| |
| | Re: LDCC Resources?
|
|
(...) for decoders, most of us are using digitrax decoders of various types. But, any DCC compatable decoder will work. The LDCC setup uses the mindstorms remote control to operate. For more info on DCC search lugnet.trains, and look at Tom's site (...) (21 years ago, 24-Jun-03, to lugnet.trains)
|
