 | | Re: Menck M154 excavator on scale 1:13
|
|
Hi Dennis It's good to see that you found the time to put an english description of your Menck online - great model! After I took the pictures of my Mountaineer and the T 282 outside I must say that everything else just isn't the right thing for a (...) (20 years ago, 13-Sep-04, to lugnet.technic, lugnet.modelteam, FTX)
|
| |
| | Re: Menck M154 excavator on scale 1:13
|
|
(...) Hi Dennis, I guess a lot of us have been waiting for the description of this fantastic model. Once again you have shown us, that nothing is impossible. Congratulation to this very fine detailled model. And the photowork is very nice, the (...) (20 years ago, 13-Sep-04, to lugnet.technic, lugnet.modelteam, FTX)
|
| |
| | Re: Menck M154 excavator on scale 1:13
|
|
(...) Wonderful model, Dennis! Like I said on Lowlug, I really like the bucket, and it looks fantastic with the Scania low-loader. One thing I'd say though is that the geared motors aren't all that bad - (URL) my CC2800> uses a single geared motor (...) (20 years ago, 11-Sep-04, to lugnet.technic, lugnet.modelteam, FTX)
|
| |
| | Re: Menck M154 excavator on scale 1:13
|
|
In lugnet.announce.moc, Dennis Bosman wrote: <snip> (...) Very nice!!! This is a great, professional-looking model. Outstanding work, Dennis! It really looks great on the Scania LS111. The detail in the model is great. It looks so real, especially (...) (20 years ago, 11-Sep-04, to lugnet.technic, lugnet.modelteam)
|
| |
| | Menck M154 excavator on scale 1:13
|
|
Three months ago I added a (URL) new model> to my website. (URL) Eventually I found some time to finish my story about the Menck excavator. I also made same extra pictures in a quarry about which I'm very satisfied. It was the first model which I (...) (20 years ago, 11-Sep-04, to lugnet.announce.moc, lugnet.technic, lugnet.modelteam, FTX) !!
|
| |
| | Re: RC racer sets
|
|
Hello to you all, "Eric Kingsley" <kingsley@nelug.org> schreef in bericht news:I28vpH.10IH@lugnet.com... (...) Dirt (...) suspension (...) experience (...) only (...) flexible (...) that (...) about (...) you (...) hand, if (...) 8369. (...) It is (...) (20 years ago, 10-Sep-04, to lugnet.technic)
|
| |
| | Re: New MOC: large crane
|
|
(...) Hi Anders and All, I'm working on an updated page for the crane. I've got some pictures of it setup at my office (it was up for an entire week), including a 2.5KG lift. I also want to take some pictures of the 6 modules that make up the (...) (20 years ago, 9-Sep-04, to lugnet.technic)
|
| |
| | Re: Re-Re-Release: Pneumatic Front-End Loader
|
|
(...) This set is in the Fall S@H catalog and also online at US S@H for pre-order. Maggie C. (20 years ago, 9-Sep-04, to lugnet.technic)
|
| |
| | Re: New MOC: large crane
|
|
Hi David, I just saw your description of the amazing crane you have managed to create. Great job, and very nice use of large turntables. I hope to see more details of the crane in the future, good luck. Best regards from Denmark, Anders Gaasedal (...) (20 years ago, 9-Sep-04, to lugnet.technic, FTX)
|
| |
| | Re: 9 Volt output
|
|
(...) Stronger :-) (...) That depends on the capacity of the batteries, normally given in mAh. AAs have more capacity than block batteries. (...) The more voltage the faster the unloaded motor runs, so then alkalines give you more speed than NiMHs. (...) (20 years ago, 8-Sep-04, to lugnet.technic)
|
