 | | Re: new jack
|
|
"Jennifer Clark" <jen@vulture.dmem.strath.ac.uk> wrote in message news:HB9vr0.64x@lugnet.com... (...) these two different designs have different functionality when two parts of boom are driven indepandantly the man in the basket can be send out of (...) (22 years ago, 5-Mar-03, to lugnet.technic)
|
| |
| | Re: new jack
|
|
(...) Sorta like the pantograph on electric trains... ROSCO (22 years ago, 5-Mar-03, to lugnet.technic)
|
| |
| | Re: new jack
|
|
"Paul Krieg" <pdkrieg@epix.net> wrote in message (...) Thanks Paul, interesting indeed! I had no idea that those machines were difficult to drive in a straight line, although I have seen one which had very large and bold arrows indicating which (...) (22 years ago, 5-Mar-03, to lugnet.technic)
|
| |
| | Re: New technic motorcycle MOC
|
|
(...) Using Mozilla ( (URL) ) set not to open Unrequested windows and not accepting cookies works fine, did not see a single pop-up! Best regards, /Tobbe (URL) SPAM when e-mailing) (22 years ago, 5-Mar-03, to lugnet.technic)
|
| |
| | Re: hoovercraft with lift, thrust and steering
|
|
"Paul Krieg" <pdkrieg@epix.net> wrote in message news:HB9KH9.8H1@lugnet.com... (...) oh G! :) what motor will rotate it? it has to create much resistance on the air (...) but it could cause the hovercraft will rotate instead of propeller :))) (...) (22 years ago, 5-Mar-03, to lugnet.technic)
|
| |
| | Re: hoovercraft with lift, thrust and steering
|
|
(...) Well, my rotor blades are a bit big (about 12 x 36 L). They do not have the profile of an actual airplane wing. They are made this way to save weight as your hoover craft is. I did not use any flex tube at this time. (...) I am considering two (...) (22 years ago, 5-Mar-03, to lugnet.technic)
|
| |
| | Re: motor for hovercraft and helicopter
|
|
(...) Of course, I have complete faith in me! :-))))) paul (22 years ago, 5-Mar-03, to lugnet.technic)
|
| |
| | Re: System-Buff needs help on his first Technic-MOC
|
|
(...) (URL) the lower end of the red 1x8. Add this part: (URL) the upper end of the red 1x8. Connect this part where there is "blank" axle between the brown connectors. Run the axle through the axle hole of the #6536 connector, and point the smooth (...) (22 years ago, 4-Mar-03, to lugnet.technic)
|
| |
| | Re: new jack
|
|
(...) Hi Everyone, AS an opperator of some of these types of lifts I thought I'de share. In my experiance some of them will let you control more than one- boom riser, boom up, b. extender, turet, tilt, etc at once. The few I've been on only up to 3 (...) (22 years ago, 4-Mar-03, to lugnet.technic)
|
| |
| | Re: new jack
|
|
"Jennifer Clark" <jen@vulture.dmem.strath.ac.uk> wrote in message news:HB84Cw.Bvv@lugnet.com... (...) thanx :) but i think to make it a little bit smaller (...) i wanted to have the piston as close as possible to the joint because of backlash and (...) (22 years ago, 4-Mar-03, to lugnet.technic)
|
