 | | Re: front wheel drive system
|
|
(...) a (...) (8 (...) Hi Josef, very nice setup ! Starting from yours, I tried to add a diff just on top of the main axle. You can support the diff with half beams, and have the space for bevel gears to engage the horizontal ones. Or use standard (...) (22 years ago, 23-Sep-02, to lugnet.technic)
|
| |
| | Re: 8735 set with too many parts?
|
|
Hello It is quite normal to have some parts extra in Technic sets. In the 8735 set which I bought there were also these same extra parts. Greetings from the Netherlands Maico Arts "Øyvind Steinnes" <senniets@online.no> schreef in bericht (...) (22 years ago, 22-Sep-02, to lugnet.technic)
|
| |
| | Re: 8480 Shuttle not locking rear wheels
|
|
<snip> (...) My father-in-law is 82 and he's not guilty at all. -- Thanx~ Nicole Drumm MS (URL) Account: drumm-family Geekshelf Account: Drumm-Family Bricklink Store: drumm_family or Drumm's Small Lots (22 years ago, 23-Sep-02, to lugnet.technic)
|
| |
| | Re: 8735 set with too many parts?
|
|
i think that it is actually cheaper for lego to make the machines that put the parts in the bag err on the side of extra than be 100% accurate and make an occaisional error of too few parts. -tk "Ross Crawford" <rcrawford@csi.com> wrote in message (...) (22 years ago, 23-Sep-02, to lugnet.technic)
|
| |
| | Re: 8480 Shuttle not locking rear wheels
|
|
(...) No, it's not normal - go back throught the instructions, and check that the gear trains mesh with the parts at the right angles as in the pictures - this is *very* important! (...) Not at all! And I feel just as non-guilty at 38! ROSCO (22 years ago, 22-Sep-02, to lugnet.technic)
|
| |
| | Re: 8735 set with too many parts?
|
|
(...) Øyvind, It is not unusual for LEGO to include extra numbers of small parts, including bushes, pins and 8 tooth gears (also 1x1 round plates etc in non-technic sets). I assume this is because the machines are less accurate counting the smaller (...) (22 years ago, 22-Sep-02, to lugnet.technic)
|
| |
| | Re: 8480 Shuttle not locking rear wheels
|
|
"Frederic SIVA" <frederic.siva@wanadoo.be> skrev i meddelandet news:H2tzB8.7Ez@lugnet.com... (...) Unfortunately, I didn't play with Technic when I was 35 (in my 'Dark Ages' at the time), but now at 48 I'm happy as a child when I get a chance to (...) (22 years ago, 22-Sep-02, to lugnet.technic)
|
| |
| | 8735 set with too many parts?
|
|
Look at this picture: (URL) at photo on backside of the instructionbook (upper right corner of picture). Arent there TOO many parts in this set? All the pieces on the table is from the newly bought set. There are 5 Techinc Pin 3/4 (partnr 32002) but (...) (22 years ago, 22-Sep-02, to lugnet.technic)
|
| |
| | Re: 8480 Shuttle not locking rear wheels
|
|
(...) I built it a long time ago, and I remember having the same problem. It's a little vague, but I seem to remember the problem was with a <part:3713 Technic Bush> on the axle that holds the wheel that blocked the movement towards the locked (...) (22 years ago, 22-Sep-02, to lugnet.technic)
|
| |
| | Re: 8480 Shuttle not locking rear wheels
|
|
(...) The first time I built my 8480, the back wheels didn't lock. I rebuilt it going back a few steps and they locked. There must be something confusing about the instructions... ust try to rebuild it. The front landing gear is pure genuis, BTW. (...) (22 years ago, 22-Sep-02, to lugnet.technic)
|
