 | | Re: 2 x4 brick down drain
|
|
(...) <snip> (...) seemed logical yesterday. scarey ;-) sheree (24 years ago, 20-May-01, to lugnet.storage)
|
| |
| | Re: Drawers vs tilt-bins and scratching?
|
|
Just hanging off of Larry's post semi-randomly.... Some thoughts on storage and building: My storage scheme is that parts which sort into a large volume get stored in Hefty One-Zip freezer weight bags, and then get stored in tubs and drawers of (...) (24 years ago, 20-May-01, to lugnet.storage)
|
| |
| | Re: 2 x4 brick down drain
|
|
(...) yeah, pretty sure. A lot of water has gone down the drain since then. What makes it so bad is that the drain was slow this morning, Gary plunged it - all the while, he teased me that it was probably a brick down the drain. It wasn't then, it (...) (24 years ago, 20-May-01, to lugnet.storage)
|
| |
| | Re: 2 x4 brick down drain
|
|
---- Begin Original Message ---- From: "sheree rosenkrantz" <srosez@hotmail.com> Sent: Sat, 19 May 2001 21:14:02 GMT To: lugnet.general@lugnet.com, lugnet.storage@lugnet.com Subject: 2 x4 brick down drain One 2 x4 brick escaped my collander to go (...) (24 years ago, 20-May-01, to lugnet.general, lugnet.storage)
|
| |
| | Re: Drawers vs tilt-bins and scratching?
|
|
(...) Yeah, spread-out space is important. But it doesn't have to be fancy. Even if one has a flip-down table-top, it'd a big help. My Dad built a train table like that - it flipped up against the wall when not in use. I've seen sewing tables like (...) (24 years ago, 20-May-01, to lugnet.storage)
|
| |
| | Re: Part Storage for Brickbay
|
|
(...) Thank Larry (...) clearly (...) I will be doing this as some parts are used, i can't say they are all new, mind you, some of the stuff is new.. If you get that :-) Still no news on Brickbay yet? -- Michael - - - Please reply on (...) (24 years ago, 19-May-01, to lugnet.storage)
|
| |
| | Re: Part Storage for Brickbay
|
|
(...) For transient storage I use the "disposable" food storage containers. They have round bottoms and cost less than 50 cents each. Not suitable for long life but work fine for me. Way better than ziplocks (which are quite a bit cheaper) because (...) (24 years ago, 19-May-01, to lugnet.storage)
|
| |
| | Part Storage for Brickbay
|
|
Hi I need a little help, with a storage solution but i don't know if you lot do the same thing I picked up a load of Lego - about 10 Gallons for 4UK pounds - which works out about $5.50 - now that's is a find :-D Anyway, i am cleaning it now, but (...) (24 years ago, 19-May-01, to lugnet.storage)
|
| |
| | Re: 2 x4 brick down drain
|
|
(...) A 2x4 is large and pointy, compared to drain pipes (a lot of which are 1.5" or 2" I.D. and that's before grease/hair etc narrow them, so it depends on how long and or twisty the run is. I'd check the trap now while there is a chance it's still (...) (24 years ago, 19-May-01, to lugnet.storage)
|
| |
| | Re: Drawers vs tilt-bins and scratching?
|
|
(...) I do the same with the larger parts...the vertical nesting stacks. I have to do the same, always running to the shelfs. Drives me nuts. I also have about twenty Plano thin, clear boxes (with lids) for the smaller parts. That helps, but still (...) (24 years ago, 19-May-01, to lugnet.storage)
|
