 | | 2 x4 brick down drain
|
|
One 2 x4 brick escaped my collander to go down the drain in my bathroom sink. Has anyone else had this experience? My sink has not slowed- yet... Will it just flush on through? Is this going to cause me problems later? I am not looking forward to at (...) (24 years ago, 19-May-01, to lugnet.general, lugnet.storage)
|
| |
| | Re: Drawers vs tilt-bins and scratching?
|
|
(...) I use pull-out drawers (IRIS) and don't have that problem. The drawers are big enough that you can pull one out 1/3 of the way and the one below it 2/3 of the way, and access both. You do sometimes find the drawer you want blocked, but if you (...) (24 years ago, 19-May-01, to lugnet.storage)
|
| |
| | Re: Drawers vs tilt-bins and scratching?
|
|
(...) In a tilt-bin setup, bins get opened only once (they stay open) no matter how many times parts are taken from them. They can also be removed. In a tray system, as at TLC, the entire drawer is a compartmentalized tray (aprox 24x30x3). It gets (...) (24 years ago, 19-May-01, to lugnet.storage)
|
| |
| | Re: Drawers vs tilt-bins and scratching?
|
|
(...) I'd like to hear more about this if it's not confidential. When I am free building or designing something new (as opposed to doing a production run where I am working from a parts list) I don't always know how much of what I will end up (...) (24 years ago, 19-May-01, to lugnet.storage)
|
| |
| | Re: Drawers vs tilt-bins and scratching?
|
|
(...) I don't think the issue of tilt shift causing wear is one worthy of consideration unless it's the only consideration. That said, I could argue that under certain working conditions, there would actually be less shifting with a tilt system. But (...) (24 years ago, 19-May-01, to lugnet.storage)
|
| |
| | Re: Drawers vs tilt-bins and scratching?
|
|
(...) Yes, definately... (...) For what it's worth, my Lego goes back 30 years (and more). I was my number one toy as a child and I made no effort to avoid scratching it. Keep in mind, that the primary components in almost any model are the ordinary (...) (24 years ago, 19-May-01, to lugnet.storage)
|
| |
| | Re: Drawers vs tilt-bins and scratching?
|
|
I'm more concerned about keeping the bricks out of direct sunlight. I avoid tiltbins for a different reason: I can't fill them up as much. If anything, I'd like to move to a system that has large opaque drawers, say 28" x 20", which can hold any (...) (24 years ago, 18-May-01, to lugnet.storage)
|
| |
| | Drawers vs tilt-bins and scratching?
|
|
I'm curious about drawer vs tiltbin storage for wear on Lego. I realize that there are personal preference issues here as well, but I'm mainly curious about the effect of tilt bins on Lego itself. Every time you open a tilt bin up, a few of the top (...) (24 years ago, 18-May-01, to lugnet.storage)
|
| |
| | Re: Building habits (Warning: Long-Winded!)
|
|
(...) <HUGE SNIP> (only for the cause of breviety) I'd like to chime in here. I fully agree with Chris here, and this is the reason why. I've been told I'm in the top 10 of documented set accumulation, (I haven't actually researched this, too busy (...) (24 years ago, 25-Apr-01, to lugnet.storage)
|
| |
| | Re: Building habits (Warning: Long-Winded!)
|
|
In lugnet.storage, Jonathan Dallas writes: <snip!> (...) My question to you is: where do you find the time NOT to sort your collection? My LEGO collection was still relatively small (~ 5,000 pieces) when I realized just how much time I was spending (...) (24 years ago, 25-Apr-01, to lugnet.storage)
|
