 | | Communication between NQC and VisualBasic
|
|
I would like to experiment with communication between two autonomous robots. Unfortunately I can't afford a second RCX. So I would like to this thing with the RCX and my PC. Is there a way to write a NQC program that interacts with a Visual Basic (...) (24 years ago, 30-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: monitoring motor revolutions
|
|
(...) Hi Kris, In addition to Lester's comment here some ideas and statements regarding your project. As Lester stated, you will need accurate distance, speed and direction measurements - and that is so true. Furthermore, for calculating coordinates (...) (24 years ago, 29-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: monitoring motor revolutions
|
|
(...) The type of navigation you seem to be talking about is called "dead reconning" by aviators. This method requires accurate distance, speed and direction mesurments. Counting motor revolutions does not even tell distance if the surface has (...) (24 years ago, 28-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
| | monitoring motor revolutions
|
|
I am currently working on a program that will monitor where a RCX goes. I am trying to establish a coordinate system so if it finds a light it can tell the location of the light. I was thinking about monitoring motor revolutions, but then I am (...) (24 years ago, 28-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RIS 2.0 - when, where, what??
|
|
(...) USB/SERIAL you mean. (...) Yes, if it works like the PC once it's plugged in the drivers tell the OS that there is a "Serial Port" for it. Then it works just fine. (...) (24 years ago, 26-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RIS 2.0 - when, where, what??
|
|
Great info! USB IR tower sounds good, I want to use my IR tower with my iBook, but I'm too lazy to buy an USB/Parallell port... I'm planning to use MacNQC then, but AFAIK, MacNQC doesn't "know" that there is a USB port on my computer... Or will it (...) (24 years ago, 26-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RcxCC control of Scout
|
|
(...) I don't think RcxCC supports Scout. You may be able to get it working by setting the environment variable NQC_OPTIONS to "-Tscout" (add an appropriate set command to autoexec.bat). Another option would be to use NQC directly from the command (...) (24 years ago, 26-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
| | RcxCC control of Scout
|
|
I'm new to NQC, but buit the tag robots from the bvandam site. The download to the RCX went ok, but the one to the scout doesn't seem to work. What are the steps required to download and run a program on the scout? I've been using RcxCC, is this an (...) (24 years ago, 24-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Connection between two different teams of robots
|
|
(...) I think that should work. I have only two teams, that means I could use the same coding system you used for two robots (they just need to know they are in the same team) so I have a lot of bytes available to transmit a message. If the (...) (24 years ago, 23-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Connection between two different teams of robots
|
|
Hi Giancarlo, I had a similar situation but only with two RCXs which had to exchange information with another constantly. Since both of them were sending and transmitting via their IR interface, the messages had to be identified and assigned to the (...) (24 years ago, 23-Nov-00, to lugnet.robotics.rcx.nqc)
|
