|
|
 | | Re: using MacNQC with Spybotics via USB Tower
|
| (...) It is a capability of NQC but I was mistaken about the Mac version of NQC. It currently does not support the Spybotics target when the USB tower is used. One of the first changes I made when I took over NQC was to add the ability for NQC to (...) (20 years ago, 29-Dec-04, to lugnet.robotics.spybotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
| | | | | Errors while installing brickOS 0.2.6.10
|
| Hi, I am a newbie. I have encountered some errors while installing brickOS 0.2.6.10. (URL) anyone encounter the same problems before? 1. When I just start cygwin, it gives me an error message like this: This application program can not be executed (...) (20 years ago, 2-Dec-04, to lugnet.robotics, lugnet.robotics.cybermaster, lugnet.robotics.edu, lugnet.robotics.rcx, lugnet.robotics.rcx.legos, lugnet.robotics.rcx.nqc)
| | | | | Re: Motor Speed Control
|
| (...) That's the case too for Swan firmware with standard parameters. (...) And yes, power consumption is much higher using on break. I measured variation of RCX current with one motor, power level 3 (50% duty cycle). Idle RCX current (35mA) is (...) (20 years ago, 1-Dec-04, to lugnet.robotics.rcx.nqc)
| | | | | RE: Motor Speed Control
|
| (...) :) (...) I'm not sure how the Swan firmware does it, but I have mine set so it cycles every 8 ms. It's on for 0 to 8 ms, then off (brake) for the rest, depending on the speed. That's fast enough to produce a very smooth result. There is no (...) (20 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
| | | | | RE: Motor Speed Control
|
| (...) Actually, it's more like standing on the brakes, letting go and then gunning the gas, stepping off the gas and standing on the brakes :-) And yes, that WILL use more gas, and more batteries. Now, if the resolutiion of timing for the brake (...) (20 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
| | | | | RE: Motor Speed Control
|
| (...) Yes, but I think the "power" portion of the cycle will draw more, because it's always trying to go from stop to full speed. Like driving a car with the brakes on. Start with the brake totally pressed, and the more you push on the gas, the less (...) (20 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
| | | | | RE: Motor Speed Control
|
| (...) The brake function (as far as I know) should not use more battery power as the short circuit is in the driver chip itself. The drivers are MOSFETs, so setting the H bridge to brake does not actually apply any battery power to the motor (...) (20 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
| | | | | Re: Motor Speed Control
|
| (...) If you are not concerned with remaining pure, this interface (URL) should provide better feedback than the rotation sensor. -Rob A> (20 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
| | | | | Re: Motor Speed Control
|
| (...) I've been using a power/brake method (instead of power/float) for quite some time in BrickOS. That was one of the first big steps in getting my Legway to work. ( (URL) ) It allows you to program a robot to make smooth turns (slow, instead of (...) (20 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
| | | | | Re: Motor Speed Control
|
| (...) I'm doing somthing similair at the moment. My robot runs along a track and needs to be controlled so it doesn't go too fast. I've successfully written some code which limits the top speed, you may be able to modify it or just incorparate ideas (...) (20 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
|
|
