 | | Gcc Problems
|
|
Hello, There is a line under Hitachi H8 tool prefix that goes like this: HMSTOOLDIR=/usr/local/crossgcc. I changed it to HMSTOOLDIR=/usr/local and I changed TOOLPREFIX=$(HMSTOOL...tachi-hms- to TOOLPREFIX=$(HMSTOOL...i-hms/bin. After looking through (...) (22 years ago, 9-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Gcc Problems
|
|
Some versions of the gcc executables are named h8300-hms-*.exe (ex: h8300-hms-gcc.exe) The Makefile.common, as you pointed out expects h8300-hitachi-hms-*.exe If this is what you are experiencing, then you have two options: 1) make copies of them, (...) (22 years ago, 9-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Gcc Problems
|
|
(...) Your previous post indicated that you were running under cygwin, iirc, so the line to which you refer above is not where your problem lies. In Makefile.common there are several sections that only apply to a particular operating system, cygwin, (...) (22 years ago, 9-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Gcc Problems
|
|
Hello, I looked at the Makefile.common file and there is a line that goes as follows: TOOLPREFIX=$(HMSTOOL...tachi-hms- Could this be where my problem lies according to what I said in the previous post earlier today? Thanks Much, Rick Bonari (22 years ago, 9-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Cygwin/Gcc/Legos Installation
|
|
Hello, Need some help on deciphering the following Errors: Errors when executing the Make Depend Command: ...../h8300-hitachi-hms-gcc: not found make [1]: ***[depend] Error 127 make: ***[depend] Error 2 Errors when executing the Make Command: (...) (22 years ago, 9-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | finally works
|
|
finally works.... the problem was in the Makefile.common file, finally change the line: # LEGOS_ROOT=$(HOME)/legOS/ with: LEGOS_ROOT=/legOS-0.2.6/ thanks a lot for your posts!! :-) (22 years ago, 8-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: legOS library path
|
|
(...) Ok. So for cygwin, the path is /legos-0.2.6 (...) Is that right? I think it must read c:\cygwin\legos-0.2.6\mycode. (...) Ok. (...) That is ok. (...) First the good news: Makefile.common and Makefile.user are correctly included. Otherwise, the (...) (22 years ago, 7-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: legOS library path
|
|
(...) To make it so that your code can live anywhere (i.e., not necessarily beneath the cygwin and/or BrickOS root directory you should make the following changes to your Makefile. 1. replace any relative paths (i.e., ../ or ../../ etc.) with (...) (22 years ago, 8-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: legOS library path
|
|
"Germán Rojas" <ge-rojas@uniandes.edu.co> wrote in message news:H3MD68.M72@lugnet.com... (...) Hi there! (...) [snip] (...) [snip] (...) [snip] This broke for me between legOS 0.2.5 and 0.2.6 I belive (and is still broken in the current brickos (...) (22 years ago, 8-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: legOS library path
|
|
"Germán Rojas" <ge-rojas@uniandes.edu.co> wrote in message news:H3Mp27.CBz@lugnet.com... (...) <snip> (...) <snip> You should add 'mycode' to the list of directories found in Makefile, just after demo. Then always run make from the legOS root (...) (22 years ago, 7-Oct-02, to lugnet.robotics.rcx.legos)
|
