 | | Re: BrickOS & Cygwin
|
|
(...) You bet. I've fixed this in CVS so it will be in our next test release. Thanks for reporting it. (This is why we do test releases ;-) Regards, Stephen -- Stephen M. Moraco stephen@debian.org (22 years ago, 19-Nov-02, to lugnet.robotics.rcx.legos)
|
| |
| | BrickOS & Cygwin
|
|
I've downloaded and installed test release 09. Once again things worked very well. But there is one definite problem with this release (as well as 08) when running under Cygwin. In Makefile.Common the lines ifdef BUILDING_HOST_UTILS # ---...--- # (...) (22 years ago, 19-Nov-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
(...) As it is, it seems[1] that two of the three NAND gates in the 74HC10 are being used as a driver for speaker output (it's odd that it's two, not one though). So, this leaves one three input NAND gate to do the decoding. Now that I think about (...) (22 years ago, 14-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
<snip> (...) Ok, thank you for the explaination! I am thinking that the Memory Manager would need some rework to support this, since the start of memory is currently established at compile time. I will have to take a look at this (time allowing). (...) (22 years ago, 14-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
(...) I have implemented what Mark Riley has suggested. I submitted a patch to the patches section at the sourceforge project page. The changes are quite small but require some tricky tweaks to the build process. I have only minimally tested it and (...) (22 years ago, 14-Nov-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
(...) While you are at it you could also make a remark near the explanation of the f000 motor control register, and make it clear that this is a hardware function. When I started to use this extra memory in leJOS I missed the remark at the very end (...) (22 years ago, 14-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
(...) In that case, why didn't the RCX designers use an 8 input NAND to decode their addresses, to leave more of the RAM usable? Maybe there werent aware of this possibility? Jürgen (22 years ago, 14-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
It also turns out that there are 8 bytes of external RAM that peek through at addresses 0xff80-0xff87. Writes to these locations also affect the motor control register. I suppose there's a small advantage in using these registers to control the (...) (22 years ago, 14-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
(...) This is interesting. It makes sense that the memory backing these locations still works, but I never would have thought to try to use it. I will make a note of this on my pages. -Kekoa (22 years ago, 13-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
(...) Interesting, I never looked at that version. I think the one disassembled by Kekoa is 0309. Current versions of leJOS also use this upper memory to store part of its firmware (almost 3K). Jürgen (22 years ago, 13-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
