|
|
 | | Re: Strip Command
|
| (...) In Makefile.common in the util subdirectory this code ifneq (,$(findstring $(OSTYPE),cygwin32 cygwin CYGWIN_NT-4.0 CYGWIN_NT-5.0 CYGWIN_NT-5.1 WindowsNT Windows_NT)) EXT=.exe CC =gcc CFLAGS+=-D_WIN32 endif pretty much guarantees that your (...) (22 years ago, 11-Oct-02, to lugnet.robotics.rcx.legos)
| | | | | Strip Command
|
| Hello, When I do a uname command, I get CYGWIN_98-4.10. It definitely appears that makefile.common has some problems with paths, etc. When I type the command: strip fontdesign.exe dll.exe makelx.exe fixdeps.exe genlds.exe firmdl3.exe as I mentioned (...) (22 years ago, 11-Oct-02, to lugnet.robotics.rcx.legos)
| | | | | BrickOS issues
|
| First off, I'd like to say that I had ZERO problems installing, building, and testing BrickOS on my PC. That's even with the BrickOS name change release and the pre-built Hitachi tools. You guys do good work! There are a few issues I have come (...) (22 years ago, 11-Oct-02, to lugnet.robotics.rcx.legos)
| | | | | Re: Cygwin/Gcc/Legos-0.2.6 Installation
|
| (...) Something is definitely not quite right with your setup. Makefile.common in the util subdirectory of the BrickOS tree has the following code in it: # # WindowsNT/Cygnwin, test against several values: # ifneq (,$(findstring $(OSTYPE),cygwin32 (...) (22 years ago, 10-Oct-02, to lugnet.robotics.rcx.legos)
| | | | | Re: Cygwin/Gcc/Legos-0.2.6 Installation
|
| Rick, I have never used 'make strip' and have been using legOS/BrickOS for quite some time now. So, if it doesn't work, that should not stop you from continuing. However, with BrickOS, the make strip command now executes 'strip fontdesign.exe (...) (22 years ago, 10-Oct-02, to lugnet.robotics.rcx.legos)
| | | | | Cygwin/Gcc/Legos-0.2.6 Installation
|
| Hello, I finally got make to complete without any apparent errors. At the end of the process, no errors were shown. I had to move the proper copy of objcopy.exe to the required directory and I also had to copy the proper copy of g++.exe to the same (...) (22 years ago, 10-Oct-02, to lugnet.robotics.rcx.legos)
| | | | | Re: Gcc Problems
|
| Rick, It sounds as if you have gcc working, however, the version of objcopy that you copied from another folder is incompatible with the hitachi h8 version of gcc. You need to have a special version of objcopy that is designed for the h8 (the RCX). (...) (22 years ago, 9-Oct-02, to lugnet.robotics.rcx.legos)
| | | | | Gcc Problems
|
| Hello, There is a line under Hitachi H8 tool prefix that goes like this: HMSTOOLDIR=/usr/local/crossgcc. I changed it to HMSTOOLDIR=/usr/local and I changed TOOLPREFIX=$(HMSTOOL...tachi-hms- to TOOLPREFIX=$(HMSTOOL...i-hms/bin. After looking through (...) (22 years ago, 9-Oct-02, to lugnet.robotics.rcx.legos)
| | | | | Re: Gcc Problems
|
| Some versions of the gcc executables are named h8300-hms-*.exe (ex: h8300-hms-gcc.exe) The Makefile.common, as you pointed out expects h8300-hitachi-hms-*.exe If this is what you are experiencing, then you have two options: 1) make copies of them, (...) (22 years ago, 9-Oct-02, to lugnet.robotics.rcx.legos)
| | | | | Re: Gcc Problems
|
| (...) Your previous post indicated that you were running under cygwin, iirc, so the line to which you refer above is not where your problem lies. In Makefile.common there are several sections that only apply to a particular operating system, cygwin, (...) (22 years ago, 9-Oct-02, to lugnet.robotics.rcx.legos)
|
|
