 | | Re: LegOS 0.2.5 and LNP
|
|
(...) On the RCX the LNP handlers are called from an interrupt handler, so after the execution of lnp_*_set_handler() you can safely assume that the old handler will not be called any more. On a PC things are different, there is a problem. I didn't (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: C++ OverHead
|
|
I seem to recall someone doing some testing that showed that C++ programs worked out to take out somewhere around 2 to 3 times the space of comparable C programs. However, I'm sure that varies. Luis (...) ---...--- "Nobody ever said that democracy (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Speed value interpretation?
|
|
(...) As far as I can tell, the speed value really affects power output. This indirectly affects speed, but not in a very happy way. You end up with a wide range of values that give you nearly the same speed, then a very short range that decreases (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | C++ OverHead
|
|
Hi all, a simple question ( I hope) I'm running a small GA on my rcx block , and I'm fairly happy qwith my results so far, it evolves well tot he conditions, however I'd like to try something new <g>... I'm going to try to evolve sub-sumptive (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Parallel sensor problem
|
|
Hi, all. I'm experiencing a strange problem. I'm using two RCXs to control my crane, and I have a single touch sensor connected to input 1 on RCX 1 & input 2 on RCX 2. However, when I run both programs, which both have a wait_event function like: (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Speed value interpretation?
|
|
(...) Greetings! Another Ross!! That's three hangin' around here now!! Well, OK ones a Rossz, but it's close enough! (...) driven (...) have (...) two (...) you (...) hit (...) Well, you could work it out really carefully, but then you've gotta take (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Motor Speed value interpretation?
|
|
Hi all, sorry if this question has been asked before but i was just wondering what the speed values for the motors represent? i have a robot with two motor driven wheels which i would like to be able to make drive in an arc. To do this i have to set (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LegOS 0.2.5 and LNP
|
|
(...) was like this: (...) you reload (...) PC, as you are (...) thing is to read (...) place of (...) optimize it and (...) what you want (...) attribute. Yes, but I'm not sure what could happen if I change those addresses in the middle of the (...) (24 years ago, 22-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LegOS 0.2.5 and LNP
|
|
(...) Ok. Checking and testing never hurts :-). (...) It's not for performance, but for correctness. The old code was like this: if(lnp_addressing_ha...ler[port]) { ... lnp_addressing_handl...th-2,src); You first test lnp_integrity_handler and then, (...) (24 years ago, 21-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LegOS 0.2.5 and LNP
|
|
(...) you may see (...) give access (...) the handlers (...) My only (...) depend on. (...) introduce a (...) this point to (...) I think that we can use safely (CONF_TM || defined CONF_HOST) condition. I'm checking the whole patch and I think that (...) (24 years ago, 21-Jan-01, to lugnet.robotics.rcx.legos)
|
