 | | utils/Makefile.common problem - djgpp
|
|
re: legos.0.2.4 In the file Makefile.common in the utils directory is this: # DJGPP does not define OSTYPE # ifndef OSTYPE OSTYPE=$(MSDOS) endif It should be: # DJGPP does not define OSTYPE # ifndef OSTYPE OSTYPE=$(shell uname) endif With the (...) (24 years ago, 27-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: rotation sensor problem (different one this time)
|
|
(...) Nope, just rotation. Well, I can't be sure, since there are no other sensors, but since it is not permanent (i.e., I can still force it to register, just at the wrong times) I doubt I have lost the IRQ. (...) No signals at all. I'll try it (...) (24 years ago, 27-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: rotation sensor problem (different one this time)
|
|
(...) All sensors stops responding? I think that you have lost, for some reasons, the ADC sampling IRQ... If you loose this one you have lost the kick to continue sampling... Some part of code inside legOS disable IRQs... I'm not enough expert in H8 (...) (24 years ago, 27-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | further observations on rotation sensor problem
|
|
It would appear that all movements (even when things are otherwise behaving poorly) are properly processed if the movements are done manually while the robot is doing it's computational phase. It would appear that things are dropped when the robot (...) (24 years ago, 27-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | rotation sensor problem (different one this time)
|
|
This occurs very irregularly, so I'm not sure what the problem could be, but it is a whopper. After a certain amount of time running my program, (or perhaps after certain inputs-I'm not sure) it would appear that ROTATION_X stops being updated. (...) (24 years ago, 27-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: light sensor problem?
|
|
(...) I remember wondering what port 6 bit 3 did and so I think I tried setting it on and off and not noticing anything broken either way. Maybe I didn't test enough though. Somebody might want to try repeating the experiment. Some extra evidence is (...) (24 years ago, 26-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: light sensor problem?
|
|
(...) I supposed so, but only to get a "fast scaling"? (...) I can "rescale" those values by theoretical calculation and maintain >>7 or make the right conversion (0-100). Now I've done the right scaling (ready to commit), but I sincerely think that (...) (24 years ago, 25-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | RE: light sensor problem?
|
|
(...) And I'll add the reminder (for all the newbies) that without Kekoa's efforts in doing the low-level documentation, we would not be where we are today.... Thanks again, Kekoa....... As a side note, I wonder how the power to the LCD controller (...) (24 years ago, 25-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: light sensor problem?
|
|
(...) I personally forget the numbers of the lugnet posts. The gist is that the firmware and LegOS were, at the time, different in a critical way. I don't know the current status of LegOS. At the time, LegOS cycled through the 4 A/D sensors, reading (...) (24 years ago, 25-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Rotation Sensor Values
|
|
This is the whole directory command dump. These errors are half-corrected if I specify ../include/*.h in the include# line. Then I get errors about not being able to find other *.h's that the originals included. Makefile:41: .depend: No such file or (...) (24 years ago, 25-Jul-00, to lugnet.robotics.rcx.legos)
|
