 | | maximum number of variables in RCX2 ?
|
|
When using the RCX2 target, the NQC manual (Section 2.2.4) states that 32 global variables, and 16 local variables (per task) are allowed. Does this mean that the whole program can only have 48 variables total when using only one task, ie. "main" , (...) (23 years ago, 20-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: problems using firmdl3 and dll on Red Hat 6.2
|
|
(...) That file should just be a soft link to /etc/rc/init.d/gpm (or ../init.d/gpm), so there's no need to keep it. ROSCO (23 years ago, 19-Feb-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BricxCC release 3.3.3.8
|
|
John Hansen wrote: > In lugnet.robotics.rcx.nqc, Stef Mientki writes: > >>I know the cause, you know the solution ;-) >> >>The size of BricxCC when opening the first file, depends on the SIZE of >>the file to be opened. >> 8 bytes, window stays as (...) (23 years ago, 19-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: BricxCC release 3.3.3.8
|
|
(...) Yes that's exactly what I'm trying to say !! To day I had an even stranger experiences: 1. the size of BricxCC became smaller after opening the first file, still depending on the size (or is it the content) of the file 2. in one of the tests I (...) (23 years ago, 19-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: problems using firmdl3 and dll on Red Hat 6.2
|
|
(...) Oh, on the console you might have gpm running, which allows copy-paste on the console with the mouse. As root, run '/etc/rc.d/init.d/gpm stop' and see if it gets better. To turn that off completely edit /etc/sysconfig/mouse and set (...) (23 years ago, 19-Feb-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: problems using firmdl3 and dll on Red Hat 6.2
|
|
It is working! In case anyone else encounters this issue... here is the solution. Per Geoff Gerrietts: (...) I just moved the file to /unused (in case I wanted it back) and reboot'd. IR communication is working perfect. Thank You Geoff! <snip> (next (...) (23 years ago, 19-Feb-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BricxCC release 3.3.3.8
|
|
(...) Well, I'm stumped. I cannot get the behavior you describe to occur no matter how hard I try. I'm not sure what you mean by "I know the cause, you know the solution". Have I understood your description of the problem correctly? Are you saying (...) (23 years ago, 19-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: problems using firmdl3 and dll on Red Hat 6.2
|
|
"Joseph Woolley" <jwoolley@spamblock....ht.rr.com> wrote in message news:GrqxJG.Cwq@lugnet.com... (...) to (...) Also, when I installed RH, I had a mouse connected to the same serial port. I am wondering if the mouse driver is still loading and (...) (23 years ago, 18-Feb-02, to lugnet.robotics.rcx.legos)
|
| |
| | problems using firmdl3 and dll on Red Hat 6.2
|
|
I recently cleared off my laptop HD and installed Red Hat 6.2, then downloaded and installed all the packages listed in the legOS HOWTO... but have run into a couple snags. 1st and most important, I am not able to send anything via the IR Tower. (...) (23 years ago, 18-Feb-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BricxCC release 3.3.3.8
|
|
hi John, thanks for your attention. I know the cause, you know the solution ;-) The size of BricxCC when opening the first file, depends on the SIZE of the file to be opened. 8 bytes, window stays as it is 256 bytes, blows the window up to about (...) (23 years ago, 18-Feb-02, to lugnet.robotics.rcx.nqc)
|
