 | | Re: problems using firmdl3 and dll on Red Hat 6.2
|
|
It is working! In case anyone else encounters this issue... here is the solution. Per Geoff Gerrietts: (...) I just moved the file to /unused (in case I wanted it back) and reboot'd. IR communication is working perfect. Thank You Geoff! <snip> (next (...) (23 years ago, 19-Feb-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BricxCC release 3.3.3.8
|
|
(...) Well, I'm stumped. I cannot get the behavior you describe to occur no matter how hard I try. I'm not sure what you mean by "I know the cause, you know the solution". Have I understood your description of the problem correctly? Are you saying (...) (23 years ago, 19-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: problems using firmdl3 and dll on Red Hat 6.2
|
|
"Joseph Woolley" <jwoolley@spamblock....ht.rr.com> wrote in message news:GrqxJG.Cwq@lugnet.com... (...) to (...) Also, when I installed RH, I had a mouse connected to the same serial port. I am wondering if the mouse driver is still loading and (...) (23 years ago, 18-Feb-02, to lugnet.robotics.rcx.legos)
|
| |
| | problems using firmdl3 and dll on Red Hat 6.2
|
|
I recently cleared off my laptop HD and installed Red Hat 6.2, then downloaded and installed all the packages listed in the legOS HOWTO... but have run into a couple snags. 1st and most important, I am not able to send anything via the IR Tower. (...) (23 years ago, 18-Feb-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BricxCC release 3.3.3.8
|
|
hi John, thanks for your attention. I know the cause, you know the solution ;-) The size of BricxCC when opening the first file, depends on the SIZE of the file to be opened. 8 bytes, window stays as it is 256 bytes, blows the window up to about (...) (23 years ago, 18-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: BricxCC release 3.3.3.8
|
|
(...) I can't duplicate this behavior. I think it might have something to do with those pesky DSK files (maybe?). Can you check to see if the files listed in your recent file list have associated desktop files (*.DSK)? Thanks, John Hansen (23 years ago, 18-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Connecting a non-Lego motor with external battery to the RCX
|
|
(...) If the motor runs on 9V anyway, just hook it up to RCX directly (assuming it only draws 500ma). If it needs more than that, hook an external battery up to it via a power transistor (either bipolar or FET). You'll need a resistor in series with (...) (23 years ago, 17-Feb-02, to lugnet.robotics.rcx)
|
| |
| | Re: multiplexor and legOS
|
|
I'm not sure if anyone is trying out my multiplexor patch, but thought I'd let you all know that I posted a new version which works better and solves some problems in the earlier revision. The patch is available in the legOS patch section on (...) (23 years ago, 17-Feb-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BricxCC release 3.3.3.8
|
|
hi John, everything seems to work fine now, I couldn't get it slowed down. A funny effect, everytime you start BricxCC, it sizes to the previous size, ok. Now opening a file (from the recent file list), BricxCC fills the whole screen. Thanks for the (...) (23 years ago, 17-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Connecting a non-Lego motor with external battery to the RCX
|
|
I need to connect a non-Lego motor to the RCX, and use an external power supply such as a 9V battery to drive the motor. Any suggestions as to how I should do this? (23 years ago, 16-Feb-02, to lugnet.robotics.rcx)
|
