 | | Re: BricxCC release 3.3.3.8
|
|
Hi John, I've played a bit with 3.3.3.8 release, and I didn't experience slowdown (it needs confirmation, but you seem to have fixed that!) The new installer went fine on my machine. I miss a feature: some mean to conveniently switch between open (...) (23 years ago, 16-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Using USB Tower with Alternative Firmware
|
|
Hi, AFAIK only the following changes need to be made to a COMM-driver to work with USB (Windows only): First of all the Lego-USB-Driver has to be installed (happens automatically when you install the MindStorms/RIS-software). (In Control Panel the (...) (23 years ago, 16-Feb-02, to lugnet.robotics.rcx)
|
| |
| | Re: BricxCC release 3.3.3.8
|
|
(...) I'll let you know... (...) My sanity thanks you! (...) Thanks again! (...) You never fail to impress me with the speed of your updates. Don't tell my employers though, they'll expect the same from me. ;-) Matthias Jetleb (23 years ago, 16-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | BricxCC release 3.3.3.8
|
|
I am hesitant to announce that I've uploaded a new version of BricxCC to my website. This release comes in a full-featured install executable. As a result the download is a bit larger (i.e., 1.6MB). This release hopefully will fix the problems some (...) (23 years ago, 16-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: BricxCC release 3.3.3.7
|
|
(...) This is great! I'm glad more than one user is experiencing this as that makes it more likely I'll be able to figure out the problem. Can any of you three who have reported this problem run a few tests for me? I haven't yet been able to (...) (23 years ago, 15-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: BricxCC release 3.3.3.7
|
|
(...) Whoops. I totally screwed that up. I apparently put an old EXE in the ZIP file. I need to seriously improve my configuration management! :-) Sorry about the mixup. I'm not going to release again until I'm sure I've tracked down and fixed the (...) (23 years ago, 15-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Power to RCX
|
|
(...) Yes, but any regulator would convert power uselessly into heat, probably too much if you use a much higher voltage and draw some current. It would be better to use higher voltage motor controllers directly (if they exist). And of course this (...) (23 years ago, 14-Feb-02, to lugnet.robotics.rcx)
|
| |
| | Re: Power to RCX
|
|
(...) Utter nonsense until you destroy the controller itself. Remember, while the Lego motors can take a fairly substantial voltage without being destroyed, the same is not true of the motor controller within the RCX. There is a voltage limit for (...) (23 years ago, 14-Feb-02, to lugnet.robotics.rcx)
|
| |
| | Re: firmware & NQC - free?
|
|
This is my dilemma: I work for an organization that encourages schools to teach engineering through the RIS using NQC. I'm creating very detailed instructions on how to install NQC and using firmware, etc. Now since this is a package of information (...) (23 years ago, 13-Feb-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: firmware & NQC - free?
|
|
Yes, it is available here (URL) (along with a firmware download program - this one is Windows only) Philo www.philohome.com (...) (23 years ago, 13-Feb-02, to lugnet.robotics.rcx.nqc)
|
