 | | Re: maximum current of outputs
|
|
(...) What part of the world do you live in? I'm in North America. I've checked the power levels very carefully to make sure my custom stuff would still work. If it's different with 220 volt stuff. Dean (...) -- Dean Husby LUGNET Member #320 TFM's (...) (23 years ago, 8-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: SetWatch() only accepts constants
|
|
(...) Sorry, the opcode requires constants - there's not much NQC can do (aside from generating an enormous switch statement). Dave (23 years ago, 8-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: maximum current of outputs
|
|
In my layout, I used Train power supply for RCX to drive train, the max voltage is 9.7v. Zhengrong (...) (23 years ago, 8-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Help needed for an NQC newbie
|
|
Thanks a lot. I added the while statement and it worked. As far as the value of the light sensor, I kept the value I had and it worked correctly. I will post pictures of the setup after the weekend and you will understand. Jude Thanks again for the (...) (23 years ago, 8-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Help needed for an NQC newbie
|
|
Try this. I had to change the value of the light sensor and add a While (true) statement. task main() { SetSensor(SENSOR_3,S...ROTATION); ClearSensor(SENSOR_3); SetSensor(SENSOR_2,S...OR_LIGHT); SetPower(OUT_A,2); while (true) if (SENSOR_2<40) { (...) (23 years ago, 8-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: SetWatch() is remembered?
|
|
(...) The Watch will reset to 0000 when you turn off device. It gets cleared on power up every time. You can, however, start and stop programs and keep the time. Dean -- -Dean Husby LUGNET Member #320 (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: maximum current of outputs
|
|
(...) 9.3x volts when a Train Power supply is used. Down to as little as 6.5 volts when batteries are getting pretty low. Dean -- -Dean Husby LUGNET Member #320 Co-Founding Member: VLC (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: SetWatch() only accepts constants
|
|
(...) You can use the NQC -watch now command to set the time. Dean (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Help needed for an NQC newbie
|
|
Hi, Normally you can see me in .space, .loc.ca, or org.ca and the like. But now that I have an RCX I want to program a bit. I have written my first NQC program and compiled it using RCXCC. I then downloaded it to my RCX but when I press run the legs (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: transfer data failed
|
|
(...) I am using 0.2.4 under windoz and have had similar problems. I found that I must use the slow download option (-s) for the firmware to load properly. regards (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.legos)
|
